Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The Switch Broke...Absolutely Fell Apart.
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid
Removed 2 screws holding left side of ice tray. Removed 4 screws holding back of freezer compartment in place. Pulled center plastic air duct out of freezer. loosened two screws holding fan mount on either side of central fan hole. Pulled top of freezer compartment back down to expose fan and mount. Removed fan mount screws and unplugged fan. disassembled fan mount and removed fan blace from motor. reassembled mount and motor being sure rubber bushings are in place. Put fan blace back on new motor (slip fit). Remounted fan mount on freezer back and plugged in. Reassembled in reverse order. This time I kept the old motor (2nd one in 3 years) so I can identify the replacement easily by photo.
My old icemaker lost some of the nonstick surface and the ice didn't want to come out
I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!
freezing of evaporator and no cold airflow to fridge side from freezer.
First i unplugged the appliance!!! Then I removed the three screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. installed fan. Removed inside panels from back of freezer and de-frosted coils with hair dryer (20mins). CAUTION! "Mop up and dry area of exsess water before pluging appliance back in! Re- assemble panels and plug in.
Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.
unpluged frig, removed rear cover removed 120v supply connector, removed three fan support screws.Changed fan blades to new motor unit installed fan support screws,installed 120v connector plug frig in, test fan installed rear cover .....
The gasket is sandwiched between the main door and the shelf assembly.
What holds them together is 42 1/4in hex head self tapping screws that run along the edge (each one is finger tight).
I would highly recommend a power drill with a 1/4 hex socket to remove the screws. It makes things much faster. Be careful when screwing the screws back in with the power drill(you only want them finger tight). If the screws are too tight,the gasket will bulge out in places.
At first the seal may feel weak. Keep the door closed for a couple of hours and the seal should improve.
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced. reassembled the pieces.
Ice maker eitehr wouldn't make ice, or made odd shaped cubes
First, I shut off the water going to the refrigerator, then removed the ice bin. Then I loosened the two screws on the top of the ice maker (the one toward the front was a little tricky, since you can't see it at all), then removed the screw that fastens the lower bracket to the side of the frig. Then I lifted up on it slightly to remove it from the two upper screws, then unplugged the wiring harness from the side of the refrigerator and lifted the whole unit out of the frig.
I then removed the plastic cover on the front of the ice maker, pressed on the tab to remove the wiring harness from the old ice maker, and installed it on the new ice maker. I then removed the metal arm from the old ice maker and installed it on the new unit as well. The last part that I moved from the old ice maker to the new one was the lower bracket, as the bracket on the new ice maker was bent during shipping.
Once those parts were swapped, I put the plastic cover on the new ice maker, plugged the wiring harness back into the side of the frig, routed the fill tube into the back on the ice maker assembly, and set the unit back on the two upper screws. I then put the screw back in the lower bracket, tightened the two upper screws, and then put the ice bin back in and turned the water back on. After a couple of hours, I threw out the first couple of batches of ice and it is now working as it had in the past.
I also noticed, when looking at the old ice maker, that the black plastic coating was coming off the ice cube tray, so it was a good time to be replacing it anyway. Overall, a very easy job (I was prepared for swearing, parts being slightly off, etc.) and it would have been a shame to have paid someone to do it.
it kept kicking on and off the relay would kick out.
just took a screwdriver and prized of the little ketch that holds it on and then unpluged the parts then pluged them back on. i do all of my repairs myself.
Used socket set to remove screws. Removed the wire harness, then removed lift arm from old ice maker and then put lift arm on the new ice maker. Reinstall wire harness then installed back in freeze with the screws. Video was very helpful. I will do business with Partselect in the future. Shipping was very fast. Thanks Partselect
The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.
No need to repeat the other directions, everyone is spot on with exactly what to do, the ONLY thing I want to add is that prior to putting the new gasket on, throw it into the dryer for a few minutes to make it more pliable..... My problem was that it didn't seat very well, be patient, after 2 days and keeping pressure on it over night, it was a perfect fit !