MSD2756GEW Maytag Refrigerator - Instructions

Removed icemaking mechanism replaced with new. Works better than ever

removed torx screws and replaced ice bin drive ring.

Quick repair especially with YouTube video; took less that 15 mins including moving ribbon cable & fill wire. Saved at least $200.

I watched the video and did the same.I also found that the drain was stopped up in the freezer section.I blew air on the other end and cleared the blockage .Also when the old heater went out,it burned the plastic wall next to the heating element,I think there was a recall on this model years ago but I did not follow up.Its working fine now.

Simple replacement of the icemaker solved the problem. I suspect the icemaker was overfilling resulting in water flowing into the ice reservoir.

Got online typed in Maytag repairs. Watched the repair video. At that point I removed the door assembly (5 screws total) saw the broken door. Ordered the part from Partselect. Part was delivered in 3 days and installation was a very easy process.Thanks for the help.

This was about 10 time easier than I had expected (I'm in my 30s, a mom). I put this off for almost a year groaning that I would have to spend tons of money on a repair man. It was really no big deal and took under 30 minutes. I used the video from PartsSelect, and it was right on. I was initially worried because the description from the website said that the new ice maker didn't come with the 'harness" and I had no idea what that was. Its just the little set of wires that easy unclips from the old unit and pops right into the new unit. Mine was reusable, so pretty easy. The only minor issue I had was that the new bracket didn't line up comepletely with the hole in the fridge where the screw went in, but I solved that with adding a skinny washer. Would definetly recommend any common-sensed person to do this repair yourself.

I couldn't believe how easy it was since I am not the handiest guy. All it look was to switch over the wires and screw it to the inside of the freezer. I was back in business.

Shut off water and unplug fridge. Remove ice drawer. Unscrew one short nut underneath icemaker, and the two longer ones holding it to the wall of the freezer. Now remove white cover. It just needed a little jiggling w a flat head screwdriver to loosen it. Now you can see where the wire harness is connected, use the same flathead to depress the plastic pin holding it in place, and slide it out. Remove the wire harness from the metal clip on side of icemaker. Now you should be holding the old icemaker in your hands. Remove the bale carefully. Now install the bale into the new icemaker, while making sure it's in the 'down' or 'on' position. Bring the new icemaker into position, gently snap the wire harness into place, sliding the wire into the clip like it originally was. Fasten the three screws again. Then, finally, snap the white cover back into place. Slide the ice drawer back into position, turn on the water, plug the fridge back in and wait 30-45 minutes for your first batch of new ice cubes.

I watched the video on how to change the ice maker, very easily explained, and removed the old in about 10 minutes.After seeing how the old one came out it only took five minutes to install the new one. The appliance repaircompany wanted$120 just to diagnose the problem,i bought the part from partselect for$104 total. This is the forth time I've used this site and saved a ton of money.

easy, followed instructions and installed new parts.

Disconnected power--removed ice holder tray--removed ice maker end cap--disconnected electrical wires--removed one screw holding ice maker to refrigerator--lifted up on ice maker to remove it from two holders--took control wire from old icemaker and installed it on new one--reinstalled new icemaker in reverse order.

Rmoval and replacement is not at all complicated. (1)Reach behind and to the left of the icemaker and release the power plug. There is a release snap on th side of the plug. (2)Using a 1/4" nut driver remove the screw holding the icemaker to the "L" bracket at the bottom of the icemaker. (3)Using the nut driver loosen two self taping screws holding the top of the icemaker to the side of the freezer compartment.(4)Lift up on the icemaker to remove it. (5)remove the white plastic cover from the front of the icemaker (pry out at the bottom) and snap it onto the new icemaker. (6)Remove the wire sensor arm from the old icemaker and place it on the new one. (7) Remove the cable assembly (plug) from the old icemaker and fasten it to the new one. (8)Secure the new icemaker in place using the reverse order as the removal. The icemaker will take a little longer to make its first batch of ice as it will have to attain its proper operating temp (0 degrees to 2 degrees F).

Watched the video and followed the instructions ... time to repair was slightly longer than expected due to the fact that my fridge had wood panels requiring removal. Still, the video was terrific since I am a visual type person.Part Select service was amazing ... ordered one day and the part arrived at my door the very next day. Had the same type of service on a previous repair to replace the ice crushing part of the ice maker. What a company!!! Thanks so much.

Followed video from site. There was one extra wire to disconnect, but it was obvious and not really a surprise considering age of refrigerator. Great assist.