Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old bellow pulled loose and torn
Was able to remove old bellow without dis-assembly. Replacement required removing the front of the machine for access. Once the front was off, the bellow was simple to replace. Biggest difficulty is getting the top mark on the bellow lined up. It has a tendency to slip out of position while you are working the back of the bellow over the retaining lip and it is not possible to rotate the bellow after it is installed. Fortunately, the tube from the detergent tray can be rotated slightly to allow for a small amount of error. Replacing the front retaining wire and spring required three hands at one point, but was otherwise not a problem. Fortunately removal and replacement of the front of the machine is pretty straight forward. I needed to disconnect wires to set the front out of the way, but it is impossible to plug them back in incorrectly.
My husband removed the bottom panel of the washer and removed the old pump with two screws, then removed the water hose coming into the pump and unplugged the electrical push in type plug from the side of the pump. Simple reversed the process to instal the new one and replaced the front panel. Simple really...far more so than calling a repair man.
simple repair. After reading other reviews my husband was confident he too could do the repair. He was right, we were so very glad not to have had to call for service.
The rubber boot assembly is not the same configuration as the original equipment.
I had to cut new slots in the metal base of the machine cabinet to accommodate the different configuration for the rubber boot assembly. Thankfully the new pump works like a charm.
Easy fix, I remove the front lower panel and the shocks where right in front of you , with a little twist with an adjustable wrench the cam right off . I removed and the replaced and it the same when you remove the back panel. P.S when installing the shocks start by connecting to the bottom and then connect to the drum it will make it lot easier. Good luck on your repair
Door was not closing properly, broken swivel arm under hinge.
removed door from washer, set flat on table and just loosen up the screws all around, removed old hinge and replaced with new hinge, very easy. back to washing clothes.
1. Turn of hot and cold water valves. Disconnect the hot and cold water hoses from the unit back panel 2. Use a nut driver to unscrew the top screws from the unit back panel 3. Remove the top cover 4. The valve is located at the top left corner 5. Use a torx driver to unscrew the screw off the valve unit 6. Unclamp and remove the hose from the valve unit 7. Disconnect the electrical plugs from the valve unit 8. Remove the faulty valve unit 9. Connect the electrical plugs to the new valve unit 10. Insert the hose and clamp into the new valve unit 11. Place the new valve unit to the top left corner of the washer and secure it with the torx screw 12. Re-cover the top cover and secure it with screws 13. Reconnect the hot and cold water hoses 14. Re-open the hot and cold water valves. 15. Turn on washer and verify there is no leak
Washer was on a 13 inch high platform I built for front.load Heat washer and dryer. Removed 3.screws from bottom of front panel and had access to all 4 shocks..front and rear. All shocks were unattachedeither at base or on tub. Easy to install all 3 from front without moving Mach. I figured if 1 or 2 shocks failed the violent.movement broke the other 2. Purrs like.a.kitten now. No bearing.or spring.damage.
Multiple water leaks, all rubber parts are chewed up from a mouse 1/
1/4 inch nutdriver, took the top and the front panel of and renew all rubber parts / hoses. It looks less than 1 hours. All parts like factory quality, everything fits perfect.
First,we took apart the front of the washer and then we removed the old bellow and put the new one on.After we put back up the front of the washer and open the door to put the clamp on then after we unlocked it.After it was working good as new.
Remove top and front Care taken to unplug door wiring should have taken notes or photos where srews go and order remove old bellows large hose clamp and sping tensioned clip clean surfaces install new bellows on tub only put all panels and door together Connecting wiring to door and strain relief takes 2 people connect bellows to door with spring clip
Removed door from washer, remove hinge from door. Then slip in hinge and tighten hinge to door. Then attach door. It works and the most important thing the wife is happy