Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
water was leaking under the frig ,wasnt sure what the problem
decided to take a chance and replace the ice maker,so far no water leaking.feels nice to know the problem is fixed.thanks for the video on how to replace it, thanks again very easy repair
Freezer was defrosting at the wrong temperature resulting in excess frost and ice. Poor cooling!
Removed all food! I used storage boxes insulates with blankets and a bit of dry ice in the boxes to keep the food cold.
Removed bottom bin and shelf
Removed bottom cover and fan shroud, this exposes evaporator coil and the thermostat. I had to defrost the evaporator and thermostat, they were completely encased in ice.
Thermostat is clipped to the evaporator coil, simply pry it off and removed it from the wire harness. Easy! Thermostat has a connector! Installed new thermostat in the same location as the old one. Connected it to the wire harness and replace the bottom cover. Turned it on and it seems to be working fine, now three weeks after repair.
It was easy to replace the start and run capacitors. But did not fix my problem, also replaced the evaporator fan still not fixed. Pulled refrigerator out of RV and ordered a new one.
The broken tracks popped off with a little effort, and the new tracks snapped in place. No tools required, except a screw driver helped to pop the broken tracks out, and snap the new ones in place.
Fridge too cold. Food freezing. Water line frozen. Running too long.
Removed 2 screws holding cover (one on left; one behind air filter on rear wall), removed cover, removed styrofoam duct, unplugged and removed old damper. The styrofoam duct broke slightly during the removal process. This was easily fixed with some 3M spray adhesive. While the adhesive dried, I packed the air passage between the fridge & freezer with paper towels to help the fridge cycle a bit (this worked surprisingly well). After finally installing the new damper and repaired styrofoam duct, the fridge went right back to freezing the food again (I soon realized this was caused by a VERY SMALL air leak where the new damper mates with the flange located on the freezer). After making a gasket with some self adhesive1/8" thick weatherstripping and applying it to the damper, things are back to normal operation.
i noticed that no water was getting to the ice maker. rather than messing around with parts, i bought the entire unit. easy to remove old one and install new one. thanks...ice started again in about an hour. unit cost less than a service call!
Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.
After first unplugging the refrigerator from it's electrical power source,I removed the lower screw of the ice making unit with a nut driver. I then loosened the upper two screws which hold the retainer clips that secure the unit tight to the freezer wall. I then lifted the unit upward and outward a few inches to allow access to the wire harness. I unplugged the haness from rear of the freezer and removed the unit completely. To install just reverse the procedure.
This was a snap. Loosened 3 screws, removed old ice maker. Made cutout for water chute. Plugged in wiring harness plug. Installed new ice maker. Tightened 3 screws.
These brain surgeons that charge $80.00 just to show up at my house to repair an appliance are history.
Unit would not cycle and dispense ice. After replacing with new unit I disassembled old unit and detected a slight burn smell in the timer.
Unplugged refrigerator and turned off water supply. Loosened two top screws and removed bottom screw. Althought kit was supplied with multyple wiring harnesses the harness attached to unit was the correct harness for the model I was replacing. Removed and reused old shut off arm as replacement arms were shorter in reach then original. Also reused bottom unit support that was removed and replaced with one screw into unit and then into side wall of freezer. Over all time less then 15 minutes. As this was a side by side ref/freezer unit their us limited space to view support screws. I used a mechanics mirror to find upper screws. This visualization made the process go much faster. Reading the other repair stories also gave me a huge confidence boost and insite in what to expect.
Removed the screws and disconnected the electric. I put the proper electric harness on and went to fit the unit in but it didn't fit. Until I figured out that you have to use the clips from the old unit that hold the unit in place. The actually hang on them. Once I figured it out it was easy.
I removed three sheet metal screws, unsnapped the electrical pigtail. Then snapped out knock out on new maker. Matched the electrical connection, pushed it in place. Finally set new one in place, leveled it, tightened the scews and walked away.
