MFI2067AES Maytag Refrigerator - Instructions

about 30 minutes. no problem

Looked at questions, picked one that applied, ordered suggested part, fix was super easy after watching video, Frig in running, part fixed it. Very excited, Thankyou.

Unscrewed the old filter and screwed in the new one

One mnorning the temp on the frig was in the 50's and the freezer was cold. Tried to get someone to come out and repair with no luck. We purchased a new frig. Then I decided to see if I could repair the old one to use. I wish I had discovered partselect before I bought the new one. First I thought from the web site that it was a overload/relay problem so I ordered it and changed it out and it was very easy. Then that did not correct the problem so I checked further and discovered that it could be the defrost heat element and thermostat. On partselect web site I saw where if your coil is covered in ice that this could be the reason. I ordered them and watched the video of how to change them out. The video is a little misleading because chances are you will not have the room around the coil that it shows on the video and also the element and thermostat will not come as one unit as shown on the video. It is still easy to cut the wires ont he thermostat and install it. The heat element is a little tricky to get out and back in and the clips that holds yours might be a little different and more difficult to do than the video but you can do it. All in all I spent about 160. 00 And the frig is working like new.

Took the old crisper apart and removed its solid part from the plastic that was broken. Put this solid part over the new crisper and all clicked together.

Thanks to a very patient husband. He looked at the situation and methodically took the freezer drawer apart by trial and error and was able to replace the old shaft with the one we had ordered. We do not understand why this basic information is not in the manual or on the internet. It was relatively easy once we knew in what order to take the drawer apart.

squeezed in the ends of the cover to insert the posts. It was very easy! But, be careful, don't over do it, line it up first!

Drawer guides on the bottom of the crisper frame could not be glued back into place. The replacement frame arrived in 1 day. Be gentle removing crisper vent shutters, trim, and the metal reinforcement channel from the old frame! Re-install them on the new frame then hang the assembly in the fridge. Slide the drawers and glass back into place. I added a dab of clear silicone grease (bulb and socket lube)on each drawer slide.

removed bins and meat/cheese cover. Removed slider with two screws. Removed broken end cap with two screws. There is a plastic linkage to a vent in the rear. Removed three pieces from inside the end cap. These are are all snap-in parts, but require manipulation. Took some time to figure out. Same on reinstall. Cleaned up drawers and cover. Easy!

Took out the old and slipped the new

Piece of cake. Took out old filer and put in new one!

First off I had no idea how a fridge worked or where to begin and the troubleshooting section of the manual was a joke. So I took the back panel off made sure the coils underneath were clean. Took out the back panel of the freezer and made sure that nothing was frozen over and I hadn't seen excess water on the floor so ruled that out. I knew the condenser was still running so I took a shot in the dark. Ordered the part and waited for it to arrive. It took me 3 minutes to open the box and install it. Immediately knew it was working replaced the back panel and moved the fridge back.

Opened filter area door turned old filter to the left to unscrew. Took out old filter then replaced the new filter and turned it to the right to tighten it, closed cover and that was it all done.

It was very easy I just push ito n and it snaped right in.

I received the part very quickly in the mail, only 2 days later. I opened up the package and replaced the old try with the new tray and it was that simple! I couldn't believe that the replacement part only took one and a half days to get here. That was awesome! I have already used part select again and will continue to.