MFI2067AES Maytag Refrigerator - Instructions

Remove pantry drawer, lid, crisper drawers, glass shelf above crisper drawers and shelf holders. Unscrew the 3 hex-head screws that attach the end cap to the side of the fridge. Very carefully pull the end cap away from the side about a centimeter. The end cap is attached to a moving vent piece for the crisper drawers which makes them in to a big L-shape. The vent piece is snapped in to the back panel of the fridge, so those two pieces must be removed together. You need to carefully unsnap the vent piece away from the back panel while holding the entire end cap piece as well. Go slowly and feel your way through it. It is easy if you don't rush. After removing the two pieces that make a big L-shape, detach the vent piece from the end cap piece. Attach the vent piece to the new end cap piece, re-fit it all back into the back panel of the refrigerator and reattach the screws.

after following instructions of previous posters, the hardest part for me was reinstalling the deli drawer lid. I was told it had to flex a little to get it on both hinges but mine didn't flex at all so I put on the left hinge and then put the right hinge on and put the right side pantry end cap in all as one piece. That worked easiest for me.

Ordered the left and right side parts. It took 4 time for them to send me a left side. They keeper sending the right side. It turned out that the wrong part was in the wrong ben. After they sent me the correct part it only took about 20 min to fix my refrigerator.

I popped the broken panel out and installed the replacement.

Placed in window and pulled out sliders.

The pivot block looked slightly worn because the hinge door mechanism on the left door would not "close" when the door was opened. I bought the pivot block, but the fix is adjusting the dual french doors so they are even i n height at the top of the unit. Pivot block is a 2 minute job with screwdriver. Adjusting the height is a 5 minute job with nut driver.

The drawer and drawer frame needed to be replaced. The part arrived on time, was correct and the repair was very easy.

I pulled out the old crisper and put in the new one.. For the other, I had watched the video so I saw that you needed a nutdriver to remove the cap. It was easy.

I have now replaced both the left and the right side Pantry End Cap. The Left side is extremely easy, but the right side is a bit tricky due to the drawer temperature adjustment lever. This is a mecanical adjuster that is made of plastic pieces that are linked together. Not super difficult but requires a little studying while taking it apart so you get it back together the same way. All in all a very simple job ,

Removed crisper drawers, pantry lid, and rails. Removed pantry drawer. Unscrewed three bolts holding right end cap, and removed cap, taking care with temperature slide connection. Unscrewed (phillips head) drawer slide from end cap and removed temperature slide linkage and adjustment slide button. Installed linkage, slide button, and slide rail on new cap. Placed new cap in refrigerator, taking care to hook linkage into temperature slide. Reinstalled three bolts with nut driver. Reinstalled rails, pantry lid and crisper drawers.

After removing all bins and glass separator, I removed the slides and then the old end cap. I paid careful attention to the control arm that attaches into several brackets as well as at the front and rear. Getting this arm off the old cap was the hardest part of the job. It would be most helpful to have a video showing the RIGHT end cap replacement; the left end cap is easy and clean, but the right demands some manipulation of the arm which is tricky. Being careful is essential, but being too gentle didn't work. This job is perfect for a left-handed person. I spent less than 30 minutes on the job, avoided having to wait for and pay a repairperson, and had everything back together and functioning quickly. Quick shipment was terrific.

I downloaded a troubleshooting manuel and went through the diagnostics. All tests checked normal except the Ref. circulating fan, there is a high speed test with voltage check and a low speed test with voltage check. The voltage was out of range for both tests which lead me to the high voltage control board as the problem. I ordered a Ref. circ. fan just to have because it is such a crucial device for the proper operation of the appliance.

Removed all chiller and deli drawers. Unscrewed old right side bracket. Replaced with new one. $25 replacement part, 5 min later . Done. Service call out would have been $65 + cost of part + $50 for each started half hour on labor. Easy fix. Part was exactly as described. Arrived 2 days after ordering. Done.

Watch the video was very helpful. I'm just a women and I did it all by myself. Thanks for the help of the video.

It took longer to open the package than to install the new part. No tools required.