Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
1998 oven unit flashing F3
SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.
I removed door by opening it to first stop and lifted it up off the hinge's. I removed all screws that held the inner panel to the outer panel and handle. Removed inner panel from outer panel, then glass and insulation, replaced glass and insulation and panel.
Replaced screws and handle,pulled hinge's out to first stop and slid door down on hinge's. This took about 20min. to do, most anybody handy with a screwdriver can do it.
PS: shipping was fast and price was great. Thanks Bob G.
First, I would like to appreciate providing a diagram of the product with a clear schematic. It was very easy to identify the item that I was looking for(an element). The serial number shown against the schematic enabled me to identify the item and pace the order.
Second, the item was delivered on time as promised.
Finally, the item that I purchased was very easy to replace. It came in as a full assembly. Just removed 4 screws, removed the damaged element and plugged in the new one. Thats it!!!
l certainly recommend this site to others to perform a self repair of their home appliances.
Burner would only cook on high setting or not heat up at all.
Shut off power to stove. Moved stove out. Loosened screws in top and middle back of stove and removed cover. Took mental note of color order of each wire and unhooked each wire from old switch and reattached to new switch in exact order of color of wire as original. Remounted cover on back of stove and reattached screws. Turned on power and turned on burner and tested burner for heat. Turned off burner, slid stove back and bingo - done. Saved a lot of money.
I unscrewed the framing trim around the door, secured the new handle to the brackets and reassembled the trim....all told its about 10 screws to remove/put back in.... Thanks to Suzanne I received the replacement handle in a very timely manner from Pars Select
Remove outer panel first, outer glass and handle come off as one piece. Be carefull to secure as last screws are removed. Remove inner silver panel. Remove broken glass and replace with new. Reaassemble. Around 10 Phillips head screws altogether. Much easier than I thought
Very easy repair, the way it was packed/shipped I took the packing put around old top to keep in one peice. Two screws in front, lift top off. 8 screws to remove burners. reverse order to put back together simple.
Shipped on timely manner,I will order again from Part Select, installing was a 15 minute job, that what I did, 1 unplugged stove, 2) removed 4 screws, (2 on top bracket and 2 on back) , 3) slide unit out couple inches enough to disconnected the wires from each end of unit and removed old part, installed new unit by reconnecting end wires, pushing unit slowly toward back of oven until wires find it's right position, set it back in place with the 2 screws on top bracket and 2 screws on back, done!!
I just bought my first condo and sure enough something broke in my oven. I thought "Oh great - I'll need to buy a new one..." After some research and a friend's advice - I was assured that I only needed to replace the broiler element. After researching the issue I googled replacement parts which led me to this web-site. I was amazed how easy and inexpensive it was for me to replace the part. The directions were easy, simple, and spot-on! The instructions that were provided were easy to follow. I also utilized YouTube instructions as well for additional visual guidance. The shipping was super fast and the element was packaged very well. Thank you so much!
Stove top wouldn't come on. Oven couldn't go higher than low heat
Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00 Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine. Thank you, Thank you Part Select for your help and honesty.
Door Handle plastic part holding handle to door broke.
Ordered new handle removed door from oven by pulling up and out. Removed approximately 5 screws on bottom 2 screws each on sides. Removed side pieces. Removed front glass. Removed old door handle. Had to tap the new door screw holes to accept a 10 X 3/4" Sheet Metal screw. Installed new handle and replaced the oven glass and side pieces. Slide the door back onto oven door brackets.
I marked all wires separately attaching a paper strip with tape to each connector and made a separate small chart where each wire should attach to the bottom of the switch. On this particular model there are three or four colored wires and two have both double and single connections to the same switch so the small chart told me where a single or double connector would attach even if I lost the attached taped information. Then since wires were marked separately, even if paper was lost I could still proceed with no outside help. I had the luxury of leaving the breaker shut off while waiting for part to arrive. After arrival which was only a couple of days, I raised the stove top and let it rest on a small board maybe 1.5 feet so it would keep itself up. The under assembly was already taken loose before so I just removed the broken switch taking all wires loose, which are already marked and replaced the switch with the new one. Gently placing each wire at its place after removing the tape for that connection. After all four wires were connected I held the switch up in place while screwing the two set screws into place. Then reattached the bottom assembly cover and then let the top down and reattached the four screws, one in each stove hole to attach the stove top to the under assembly. I then reattached one element and flipped the breaker switch on. No sound or problems so I tried the element and all is well. Reattached all elements and the project is done. PartSelect.com made this repair easy and economical. Replacement would have been 4x the part and shipping. Thanks.
I turned off the range breaker and doubled checked to make sure the power was off . Using 1/4" ratchet wrench I removed 2 sheet metal screws and lifted the glass top up and held it in up with a small cardboard bow. I removed 2 more screws holding the element in place and installed new unit. I then