LSMX211ST ((00)) LG Refrigerator - Instructions

It was SO easy. No clamps or brackets. Grabbed the gasket with pliers to get started removing it - just pull it out of the deep groove inset around the perimeter of the door. Within one minute I had the old gasket removed. Started installing the new gasket by inserting the top right corner 1st (pushing the new gasket profile into the deep groove inset on the door). Working around the top and right side slowly inserting the gasket profile into the deep groove around the entire door. You may have to "adjust" a bit by pulling on the gasket but within 5 minutes I had the new gasket in-place never having to turn off the refrigerator. YouTube has great "how-to" videos. It's easy!

Pulled old gasket off by hand. New gasket was easy to install by pushing it into molded cutout in refrigerator door.
Very satisfying to have no glitches in the seamless installation.

Now that you have to buy a complete assembly that includes the drawer in the classy window it's very simple to replace however you buying parts that you don't need simply because G no longer makes the window. Which I find rather odd being as though that they make the whole assembly think and sell windows by themselves for less than 2/3 of what I spent through the whole assembly

The past I ordered was broken upon delivery. I asked for a replacement and was refunded the charge. Tried to contact you but "due to covid" you aren't taking calls. Net result: I ordered the part from another source, got it, installed easily. Won't use you again.

Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.

I actually didn't use what I got. Because there was all kinds of tubing coiled up in the door. We just fed the exsess all the way through the Fridge,and Bingo! It was done.

Just had to slip the 2 pegs into the existing holes.

I watched a couple of You Tube videos on how to make the repair, ordered a new spring from Part Select, and installed the new spring when it arrived. Took about 5 minutes for the actual repair.

Check the spring when it arrives. The first one I received was wound the wrong direction. Called customer service and they were super. Refunded the charge for the first spring, found the correct one for me, and mailed it out.

Pulled the fridge out.
Unscrewed the back cover and the one screw holding the value assemble.
undid the 2 hoses and replaced the part.

Super SImple/

Removed ice bin
Unscrew the 3 screws.
Lift ice maker for the bottom to remove it but do not pull it until the power is unplug from the part.
Install the new part the same way you removed the old part.
Turn the switch and waiting 48 hours before the ice bin start getting ice

REMOVED 4 SCREWS HOLDING UNIT IT DISCONECTED PLUG TO CONTROLER AND REMOVED IT BY PULLING OUT ON THE BOTTOM FIRST. TO INSTALL SLIDE THE UNIT UP AND IN FROM THE BOTTOM CONNECT THE PLUG AND INSTALL THE SCREWS. THE TOP SCREW HAS A PLASTIC SPACER WASHER. UNIT WILL NOT START TO MAKE ICE UNTILL IT REACHES TEMPATURE, GIVE IT TIME. WATER DESPENSER WILL WORK. CONTROLS ON THE FRONT OF THE DOOR WILL LIGHT UP NORMALY. I REMOVED MINE WHILE WAITING FOR PART TO ARRIVE, 4 DAYS. EVERYTHING WORKED EXCEPT WATER & ICE DESPENSER AND CONTROL DISPLAY ON THE DOOR.

I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.

Swapped old one with new one. New one had extra plug not needed.

I took a very thin bladed screwdriver and took the old part out -carefully.
The new part fit in quite easily.

Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.