Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LNC6766A00 > Instructions

LNC6766A00 Admiral Washer - Instructions

All installation instructions for LNC6766A00 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LNC6766A00
256-270 of 304
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Lid hinge pin broke

  • Customer: Paul from Antioch, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The videos included in the shipping notification email made the repair a breeze. The only thing not shown was (at least on my washer) that the screws that needed to be removed had torex heads instead of normal slot or phillips heads. Luckily my tool crib had what I needed.

mouse ate hole in tub to pump hose!

  • Customer: Robert from Chapin, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Slip wire clamps over tube ends. push hose ends over connections, move clamps over hose end, making sure clamps are centered on connections. Easy as could be.

Loud screech at end of each cycle and knocking sound from bearings going out.

  • Customer: Don from Osceola, IA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Tipped washer backwards and removed belt from all three pulleys. Stood washer upright again and removed back panel around pump(4-screws)Removed drain hose from house drain and emptied excess water in the pump into a bucket. Removed the hoses from the drain pump then removed the three bolts holding the pump in place. Removed damaged pump and replaced with new drain pump. Reassembled in reverse order. Once the pump cover was replaced, tipped machine on its back, replaced the belt onto the three pulleys and promptly returned machine to its upright position and ran a test load of laundry! Success! Works great!

In spin cycle, made a loud nosie

  • Customer: Vicki from Pollard, AR
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Took the back off, located problem, ordered part, removed old part, installed new one, tilled washer to put belt back on. Whole process not bad at all. Working with this site was so very helpful, will keep in in my favorites or future use. Thank You Parts Select!

change out pump bearing wore out

  • Customer: Bennett from russiaville, IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Unhook water lines after shutting off water, unplug power cord.Then move washer out into open space for easy access. Used flat tip driver to push in the spring clip to open the top of washer. Flip top up and had wife tilt the washer back. Once bottom is exposed took belt off the motor pulley. Let washer back down. Use the socket wrench to take out two ( front corners ) screws. Tilt front panel back and lift out off the clips . Water pump is front right corner. Use socket wrench to take out the three screws that form a triangle. Lift out the pump. Have something to catch water from pump . Use pliers to remove the two clamps spring from the hoses . Remove both hose from the pump. Then install new pump in the reverse order and close up washer in reverse order and put belt on . Replace washer in it place reinstall water line and lastly the power cord needs tobe pulg in. Now test the washer.

suspect motor bearings. squeeling and smelled burning

  • Customer: Peter from Voorhees, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Followed your excellent video instructions to change out the motor.

Plastic hinge at back of lid broke

  • Customer: Bill from Kissimmee, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very easy pop-ed up the top from front used my Duroc screw driver removed screw removed lid slid hinge on slid lid back in place attached screw. Make sure you get screw tighten and snug. Job Done!

Hole in hose from wear & tear

  • Customer: Richard from Las Cruces, NM
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Opened back panel. With pliers, moved the retainer clamps. Used a flat screwdriver to pry off hose from tank. procceded to remove hose from pump. Put new hose on and replaced hose clamps. Tested with a small wash cycle, no leaks. Job done.

broken hinge

  • Customer: Nick from Las Vegas, NV
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Release top of washer with putty knife (2 clips), unscrew Phillips head on hinge, replace hinge, replace screw, close washer top.

Changing Suspension Springs

  • Customer: David from Lancaster, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
The repair itself was not complicated: it was just taking off the old springs and putting on the new ones. Where it became difficult was, rather than having the appliance on a platform, I was doing it from the ground. This made it a bit hard to get some leverage to stretch the new springs into place, especially in the back. I would recommend that you have a second person there to push the tank toward the spring you are replacing. This helps reduce the distance you need to stretch the spring. If you ARE in a position to get it up on a platform, that would probably be best and would make the job much easier.

The washer making a ticking sound while in the washing and spinning mode.

  • Customer: Rudy from Yukon, OK
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I found the instructions on www.ehow.com about how to remove the shell of the washer so I could find what was going on with the washer and why it would smell like burning metal. I found it was the Drain Pump with Pulley Assembly P/N: PS2347187. It was easy to replace and saved $$$$ from having to purchase a new washer or call a repairman or women.

machine moved and shook when in spin

  • Customer: virginia from central city, KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
we followed the video instruction that was given,on how too replace the part of the snugger. it worked really well. we are pleased with everything.

washer shook uncontrollably during spin cycle

  • Customer: Adam from Plainfield, IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video but didn't remove the motor. Instead I lifted the tub through the top. I also didn't have longer screws with that thread, so I used slightly smaller diameter screws with nuts on the end and it worked great.

Pad missing from both front legs which made washer dance around the room

  • Customer: Michael from DeSoto, TX
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Easy as pie but had to cut one with hack saw to remove as it would not unscrew. Rust was the problem. Hack saw was the cure. Otherwise repair would have taken 5 minutes Washer now works as it did as a new appliance.

Screaming noise from under unit. Belt shot from under it :) No harm.

  • Customer: Louis from Goodyear, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Used Putty Knife to release a tab on left split of cover/lid assembly lifting up slightly to release the tab, then I repeated the same on the right side. With the belt already flung off of the unit, I saw the 2 screws inside left/right top corners holding the front cover On. I tilted it forward and up and released from two clips on the bottom of the unit. With the front cover removed I saw the pump on the lower right side of the tank. 3 screws and 2 hoses hold the pump in place. Once pump was removed reversed how it was taken apart.
All Instructions for the LNC6766A00
256-270 of 304