LG9801XMW1 Whirlpool Dryer - Instructions

Removed 2 screws in the lint filter and popped off the top. Removed the 2 screws holding the front panel on. Slid the drum off and set aside. Replaced support rollers. Placed the belt over the drum and placed the drum back in the dryer. Wound the belt over the tensioner and motor pulley. Turned the drum to keep seal from folding up. Replaced front and top.

Tip: Use bungee cord or rope to hold top up and out of the way while doing this job.

Extremely easy repair! Unplug the dryer. Remove the lint trap screen. Take the two screws out of the lint trap chute, pry up the top of the dryer, insert wood or have someone hold top up, remove two screws holding the switch in place while holding the switch so the old spring doesn't fall. Remove old spring and replace with new one. Re-attach switch to dryer with two screws. Plug in and test run. Lower top and push firmly to engages clips. Re-install two scres in lint trap chute followed by the lint trap screen and you are finished!

Repair took about five minutes and saved approximately $70!

Followed instructions from video, just removed lint collector, dryer top and front panel, removed broken belt and old idler pulley. Vacuumed and cleaned up inside dryer.installed new pulley and rib belt according to printed instructions,installed new dryer duct and new clamps. Saved myself huge service call or having to buy new dryer.Will be checking with this site on any future repairs instead of calling a repair service. Your video made it real easy to repair.and I am 77 years old.. Bob

The repair was fairly straight-forward. I removed the front of the dryer, lifted the top off, and then released the tension off the belt dy depressing the pulley arm. Once the belt was off, the drum came right out and then it was on to unhooking the wiring from the old motor. Very simple up till this point. The snag came when I went to unthread the impeller fan off of the old motor shaft. It was permanently sealed onto the shaft so I had to cut the old shaft into using a reciprocating saw was a metal-cutting blade. Once this was done the new motor installed easily exactly like the old one was mounted. I had to also purchase a new fan due to the fact that I was unable to remove the cut shaft from the old fan. All parts worked great and the dryer assembled back together easily. Works like a new dryer now.

Sensor is in the front lower left. Gas off, electicity off. Removed two screws for the filter, pry/lifted the top up and taped it too the overhead cabinet, removed two screws inside top of front panel, lifted pandel with door closed staight off. Two screws to remove the flame sensor braket. unplug the old sensor install the new one and reverse everything. With others suggestions I purchased temperature switches etc. but the radiant flame sensor was the problem. I now have some spare switches for future. Excellent company and very quick service. Oh, Sears wanted 200.00 just for the service call, I live rural.

For the Ignitor - As involved as taking the dryer completely apart sounded, it was super easy. 1-take out the lint trap and remove the two screws there. 2-Pop open the top with a screw driver and swing the top completely over/back. 3- remove the two screws holding in the front panel and remove the panel. 4- loosen the belt by pushing on the tension roller under the drum on the right and remove the drum (its super light) use the belt as a handle. 5- remove the screw holding in the ignitor and replace it with the new one. Be careful to not touch the new ignitor. Then go backwards putting it back together.

Really simple, the dryer repair guy I had out did not have the part and wanted $100 to fix. Did it myself quickly and easily and the dryer is working like a charm.

removed frt & rear panels & drum and lint chute for seal replacement replaced these components, problem didn't go away, ordered & replaced both gas valve coils (m series coil kit) problem solved

romoved from pkg. and fit it to the door. no tools needed. best of all the part came in 24 hrs and was fixed with out delay of waiting from a store that was out of our area. great costumer service!!!!!

Investigated inside control panel for loose wires or parts. Removed back of control panel and back of dryer and used a vacuum to remove lint from every possible contact. Problem not fixed.

Lifted top of dryer and cleaned inside. Struck door close switch with a screw driver and dryer started every time. Replaced switch.

Works every time. This is the 3rd repair in over 20 years. Each time the dryer works as though new.

Unplug dryer. Remove the front bottom panel of dryer 2 screws, then unplug wire connector to the old igniter then unscrew one screw holding ignitor then wiggle out. Open new igniter wiggle back in place insert screw tighten, (getting this screw back in is a little hard) replug wire connector to new igniter replace front panel with two screws. Plug in dryer and there you go drying clothes again. Wife all happy again.

I ordered the belt idler pully and drum support rollers and after watching the video on Parts Select web page, changed the parts. It could be done by one person, however having a second person to help with the drum installation worked great. I discovered the motor bearing on the front side of the motor was the source of the squeek. I disassembled the dryer again and removed the motor. After ordering a motor the installation and reassembly went smoothly. The parts came in two days of placing the orders and virtually new parts in the dryer makes it seem like a new machine.

Thermal fuse was blown so I replaced it. Still no heat. Hi-Limit thermostat and Cycling Thermo. had continuity as did flame sensor. Igniter tested 66ohms. I placed a wire jumper across the Hi-Limit and the igniter glowed, solenoids opened and gas came on. I orderd the Hi-Limit and since both "overheating" limiters were defective I decided to order the cycling thermo just in case. The Hi-Limit was received in 2 days but the Cycling Thermo was backordered. In the meantime my wife got antsy so I went ahead and installed the Hi-Limit and put her back in service... ...for one load. I wasn't certain if I had fried the "limiters" again but since they had continuity and I could measure continuity all the way to the Igniter I decided that it HAD to be the cause. I ignored the flame sensor since it never came into play without the igniter glowing... The igniter arrived and measured 56ohms. Hmmm... After installing the problem was solved. Word of advice: If the thermal fuse is blown and even if all else in the circuit SEEMS ok, go ahead and order the Fuse, Hi-Limit and Cycling Thermos, and the Igniter. It will take you about 30 minutes to install and you'll reduce your out-of-service time! Good luck!

1) Unplug power cable from dryer.
2) Remove the 2 screws that secure the chute for lint filter screen with
Phillips head screwdriver.
3) Remove the lint filter screen.
4) Depress plastic locking clip on each side with putty knife to release
tension and lift up top panel to clear the locking clips. Each locking
clip is located 2-1/2 inches from the front edge of side panel.
5) Lift the top panel and lean against the wall for support. If dryer top
panel cannot be raised all the way due to cabinet(s) above, tape
the dryer top panel to cabinet above or have somebody hold the
top panel for temporary support.
6) Install the new metal locking clips. Ensure that the elongated tab
of the metal locking clip is towards the front of dryer. Compress
locking clip lightly with pliers and push down into the hole.
7) Lower the dryer top panel and press it down in place over the metal
locking clips for a tight fit.
8) Reinstall the 2 screws to secure the lint filter chute.
9) Reinstall lint filter screen.
10) Reconnect power cable for dryer.
11) Turn on dryer and inspect that all dryer panels (top, sides and
front) are tight and secured.
Repair Duration: 5 minutes

Actually, I was the handy man. First I removed the front panel. Then I used 3 - 2x4s to hold up the drum. Then I slipped the belt around the center of the drum ,motor,and around the pulley at the bottom of the dryer. That was it, and then I put it back together. My wife was amazed and proud that I did it without calling for help! No Problem!