Refrigerator light not working. If I would flick the button it would go on for a minute but not stay on.
The old switch was a little hard to get out....took me a couple tries. I couldn’t move the frig out to unplug it, so just shut the power off in the kitchen. But, I was happy that’s what the problem was and so happy to have the light back on......it was probably three years it didn’t work!
Low water pressure which in turn led to no water and no ice.
Unplugged fridge, shut off water supply disconnected water supply from fridge. Remove screws that hold lower cover on back of fridge, removed screws holding valve assembly to fridge. Disconnect two electrical connections, remove black c-clip on out flow water line, lift fitting on outflow line side and pull water line off. Replace with valve assembly in reverse order
After watching a few iTunes videos I was able to order the light switch from part select and within a week I had the new switch. I had a little trouble getting the switch out. I used a flat screw driver and taped around the edge to keep from damaging the wall inside. I found the clip on the right side and had to use some force to get it popped out, you may need to use pliers to disconnect the switch.
I could not as the spring was too large and did not fit. Calls to Parts Select were not very useful as I described the problem and was told that that was the correct part, even though I supplied photos. Rather than research the problem, I was told to call LG. Not exactly the response I expected from an authorized distributor. By the way, LG service said to call an authorized distributor, so round and round I go Please help.
Pulled fridge away from wall, unplug electrical connection, open fridge door, use knife to prize out door switch, pull off and replace switch from electrical wiring.
I installed the new 3 wire ice maker very easily, but it was defective. I was told that instructions for the return of the defective part would be sent later due to the virus. I have never received the return instruction. I did receive a credit for the defective part. VERY Satisfied with y’all’s service. Waiting for return instructions if y’all still want it back. Thanks, Thomas Pennebaker
The heavy work is moving the fridge, then take off the lower plans. Use a bowel or cup for screws and the water line connector spacers so you don't loos them. undo connections holding water line, including the bottom brakes for the solenoid. Reuse the spring around the lower waterline to prevent external wear on the line.
NOTE: remove the waterline connector spacers and save! NOTE: you must compress (not pull) the connect to then pull the waterline out of the connectors. NOTE: You must also remove the water filter and housing inside the fridge but this is easy. MOTE: Test the line for leaks by turning on the water and then using the door water. The filter will need to refill so it may take a minute before water comes up. This line only have pressure when the door water is used or the ice maker needs to make ice.
After replacing the line, test the line for leaks by using the door water so the solenoid fills the lines
Initially the wrong spring was sent. The coiled spring must have COUNTERCLOCKWISE wind for this refrigerator door. A spring with a clockwise wind was initially sent. Partselect very promptly and efficiently corrected the problem at their expense. For this reason I give them a strong recommendation. View their instructions on youtube.
Unplug the refrigerator and empty the freezer. Remove the lower basket and roll out upper tray. Open the freezer door. I was able to lie on the floor to remove the 2 screws holding the ice maker without removing the freezer door. Depress the 2 tabs and slide the ice maker forward to remove. Install in reverse order. Change the water inlet valve at the same time.
Make sure you remove the double crisper frame that the glass sits on to get both the glass and frame to room (same) temperature!!!!!as easy as that!!!!!
Unplugged the refrigerator, Taped around the edges of switch as I had read to prevent possible scratches, used very thin flathead screwdriver to pry out old switch, unplugged old switch, plugged in new switch, put it back in opening, plugged fridge back in, and I had beautiful light! Hardest part was unplugging the refrigerator!
I actually took a picture of the correct spring installation at a big box store that carried LG. I had called LG, but they said they didn't have any installation brochures, and to call a registered LG repairman. That was out of the question, since the repairman would charge $100 just to show up.
I looked at the picture I took. Used needle nose pliers and inserted one end. Unless the lady of the house is very strong, this should be handled by a man, because of the rigid spring. Once the spring was inserted into one side of the flap, I used the pliers to get the other end into the proper slot. Very easy, but the spring is very strong !!
