KUIC18NNZS0 KitchenAid Ice Maker - Instructions

Took knife and pried out the the damaged switch. Took wires off. Put the wires on the new switch and put it back in the hole. Job finished. The part shipment was very prompt and I am happy. The End!

Pried out old Switch,Hooked wires to new switch Snapped in New Unit.
5 minutes Total Time

I popped the switched out depressing the underside of the switch so that it could be removed.
I ordered the part.
Paid for normal shipping.
Received an order confirmation.
Received a shipping notification.
Received the part the next morning.
Open the part and attached the wires.
Pushed the switch into the hole and the process was done in less than 24 hours. I couldn't have been more pleased. The actual installation took less than 30 seconds.

Recently unemployed, we knew a repairman was out of the question. We opted to glue the broken tab,but I knew that would just be living a substandard rerpair so looked on line. Found our replacement part very easily and much to our surprise we had the part the next day, yes, the next day!! Looking at the new part gave us the confidence to pop out the old one without causing damage to our unit. It was a no brainer , pop out and plug in w/in 30 seconds. Small appliance repairmen are a minumum of 75.00 service fee plus parts. Our repair less than 20.00 less than 24 hrs. How good is that?

Gail Costa

part got here fast and I fixed it in no time. GREAT Thanks

Popped old one out with knife. exchanged power leads. Popped new switch in. Make sure to unplug refrigerator before you start!

plugged the two wires in and snapped the switch into it's socket.

UPS delivered the part at 11:05 AM and I had it installed in less than 30 minutes. No issues, easy removal and re-installation although the compartment was very tight for my hand and a 1/4" drive socket wrench. One installation suggestion however, pre-thread the 3 mounting screw holes on the motor housing first by screwing one of the screws provided into each of the three mounting holes on the motor housing prior to attempting to install the new motor. This way you'll find it much easier to get start the screws given the very limited work-space behind the fan compartment.

Having read a few of the user reports like this one gave me the confidence to do this repair. The space was really tight, but one of the write ups suggested removing the frame and then replacing the motor on the frame. That was an excellent suggestion. The only difficulty I had was when I used the motor screws from the old motor to install the new motor. They were slightly longer and didn't tighten down all the way. So the first "test" resulted in still having a noisy fan motor because it was shaking around a bit. But, taking it back out and using the screws that came with the new motor did the trick. The refrigerator is now whisper quiet all the time. I also appreciated the conversion wiring harness in the kit that was simply plug and play for this new motor to my old refrigerator.

I pulled the back panel covering the fan and condenser off the refrigerator (just a few screws) and disconnected the fan which was a simple plug. The fan was held in place with three screws which I took out. I pulled out the old fan and replaced it with the new one, three screws to secure it in place and reconnect the fan plug. Then simply replace the back panel and plug the frig in. the fan silently started right up. Good as new and no service call! :)

Unplug regrigerator power cordfrom wall outlet. Using nut driver remove cover from lower back side of refrigerator. Unplug wire connection to fan. Using nut driver remove the four screws holding the fan/bracket assembly. Carefully remove fan/bracket assembly from refrigerator. Using nut driver,remove the old fan from fan bracket. Using nut driver install new fan on fan bracket. Carfefully install new fan/bracket assembly and install the four screws. Plug wire connection to fan (you may need to use adapter supplied with new fan). Reinstall refrigerator lower back cover. Plug refrigerator power cord back into outlet. Note: you may wish to carefully vacuum dust from back of refrigerator before installing back cover. You should also vacuum dust from front side.

Disconnected power cord, removed rear cover of refrigerator, disconnected pig tail, removed 4 housing screws, took three mount screws out and removed old fan. Reversed steps, plugged in and complete repair done.

Super simplet to fix. Popped out broken light switch and unplugged it and replaced with new switch. Received the part one day after ordering it from your company--AWESOME SERVICE AND TURNAROUND TIME!!! Saved at least $100 plus in repair costs/trip charge for something we were able to do. Great experience and would order from your company again. Thank you!

fan motor housing had to be drilled through both sides of housing to attach to existing bracket. Possible damage to wiring inside the unit may disable condensor fan motor when motherboard is replaced. (Motherboard on order.)

Pulled out the Fridge. Removed the plug. Removed the back panel screws with nut driver. Vacuumed the coils & fan area. Disconnected the fan cable. Used a socket and thumb ratchet to remove the 3 mounting screws from its sheet metal bracket. Slid the old fan assembly out. Assembled the new Fan blade onto the new motor shaft and attached the adapter cable to the fan connector. Slid the assembly into place and reattached with 3 screws using socket and thumb ratchet. Connected adapter cable to fridge harness and plugged in the power cord to test the fan. With it working Quietly and knowing the the problem was solved, the back panel was reattached.