KUDA23HYAL0 KitchenAid Dishwasher - Instructions

This repair was just so easy. I am a 65 year widow and did not want to call repair for something that I thought I could do-ordered the part and it was delivered in two days. I rubbed a small amount of vaseline around both the tube's ends, used the hair dryer to heat slightly, attached one end of the tube to the upper spray arm receiver and the other end to upper wash assembly and job completed. My savings was probably $65.00 or more for no service call. Works great and dishes are clean again.

I was about to pull out my dishwasher and then removed the bottom cover and there you could see the spring. BUT WHO KNEW THERE WERE TWO SPRINGS? Only one of mine was bad BUT I would have replaced both of them at the same time. The diagram on the website clearly only showed one spring and now to buy the second one would cost more

I took the first bumper, I had bought two, and tried to snap in on to the rack. It was too rigid and broke.

My son heated the second one in hot water and it snapped right on.

At least I know the secret to installation, but now I need another bumper.

Piece of cake --after having read what others had suggested on your webpage, I used the heat from a hair dryer which made the piece pliable and simple to fit into place. It took less than five minutes. When my husband came in from work, I proudly told him the part had arrived and it was fixed! Taa Daa!

I just pulled out the rack and removed the eight existing roller wheels and roller axles. I was able to remove most of the roller axles with my fingers but needed pliers to remove a couple of them. I then snapped the new roller axles onto the rack and then the roller wheels onto the new roller axles and put the entire rack back in the dishwasher.
The lower rack now rolls smoothly and consistently no matter how many dishes we have piled into it. Also, it has not come off the tracks since replacing the roller axles and roller wheels.

Snapped in new ones (8) by hand. I was amazed
how fast I was able to find this part online and the
ordering was easy and in a few days the parts
arrived. No hassle trying to explain to anyone what
part I needed. There were pictures of all parts
available. Ordering online, especially if you
know what you are looking for, is really the way to go.

I bought the kit because it had other parts that I thought I needed.

I am a 73 year old lady. My nephew found the torn rubber water delivery tube after a repairman had found nothing. I looked up the model number, contacted Part Select by e-mail, ordered the part ($15.++ for cost and delivery), read reviews and found tipe for installation. Total time spent on installation was less than ten minutes. The round tube, with a smidgen of liquid detergent inside each end of the tube, fits onto the water line; the other end of the tube will squeeze flat with little effort, and fits onto the apray arm.

I ordered 8 new axles and used old wheels. I broke off the remaining axle parts left on the wire lower basket with just my hands, and then popped on the new axles. This was done without tools; just needed significant pressure to pop the axles onto the coated wire. The wheels popped onto the axles with a little pressure. Make sure you have the right side of the wheel out. I simply looked at the remaining working wheels before install began to make sure which side goes out. Very easy install.

Actually I ordered the drain and wash impeller kit because it was listed as the #1 cause of failure to drain. I then hired a plumber to install it. He did so and that didn't solve the problem. So I was about to buy a new dishwasher. I then noticed that the second most frequent cause was a problem with the "dishwasher drain check valve." I watched the "partselect" video on how to change that. I didn't have a new one but I thought I would take out the part and see what I could learn. As it turned out it was blocked by a little piece of what appeared to be a walnut chip. I cleaned it out reinstalled the drain check valve and the problem was solved.

I pulled off the broken parts and snapped on the new axles, then replaced the wheels. Very simple.

i pulled the rack out, took off the old parts then added the new ones. it was quick and simple. i needed no tools and my package of parts arrived quicker than i thought. thanks!

The whole operation took about 5 minutes which included opening the package! Sprayed some vegetable spray inside the opening of the water tube that attached to the spray connection and it slipped right on. Absolutely amazing and I feel like I have a brand new dishwater! My dishes are definitely cleaner too! Thank you Parts Select for posting how to instructions!

Used screwdriver to pry off other end of water tube. Kind of cooked on over the years and rear connection point is on a part that is not real strong so you have to be careful to not break or bend the connection. New tube is very tight to get on so putting it on required using the blade of the screwdriver to get the tube to streatch over the two connection points, but not real difficult. Now it's good as new!

First removed old hose from the upper rack. Used hair dryer to heat the hose up ( hose was a little stiff) and installed hose. It's pretty simple to install, I didn't even have to unload the dishwasher