KSCS25FKSS01 KitchenAid Refrigerator - Instructions

I poped the outer cover off... Removed 3 screws and gently pulled the old timer out.... Also pulled out the ice maker arm.... Aligned the shaft of the tral to match the new motor assembly and gently slid it in... tightened the 3 screws and aligned the wire hoop back in the hole and the job was done... i pulled out the top freezer basket for easy access... Took less than 20 minutes total..The part was correct as usual.. Thank fellas

The retaining pins, which are part of the control bracket, that hold the micro switch that powers on the ice dispensor had broken, allowing the micro switch to fall away from actuator paddle. I replace the entire control bracket which holds the 2 micro switches, one for ice dispensing and one for water.

Took the old one out and put the new one in.

I removed the outside ice door panel with two flat head screw drivers inserted in the slots at the bottom of the panel. You simply pry out until the bottom releases and then you push it up gently to release the top. I then removed the hex head screws that held the outside wire panel and the switches, at this time you need to remove the old plunger that is connected to the top of the ice door assembly. I then disconnected the old heat strip and removed the hex screw that held the ice chute at the bottom. Then I removed the pin and spring that held the ice door assembly at the top. Replaced the parts with new ones provided in the kit. The ice door is no longer freezing up, nor is the ice bucket in the freezer. The freezer is now back to the right temperature, without having to be set on high

as shown in instructions

This was the easiest repair I have ever done. Don't waste your money calling a repairmain for this one. Unplug from electrical outlet, and turn off water supply. I first removed the ice bucket to give myself the room needed to remove ice maker. Then I loosened to two top nuts holding the icemaker and removed the bottom one. Pulled the icemaker away from the freezer wall and disconected the power supply. Removed unit from freezer and removed the three screws holding control motor assembly in place, gently removed icemaker control assembly. Secured with the three screws, placed unit back in freezer making sure water inlet was in place and reconected power supply. Slid unit onto the top two nuts and tightened and replaced bottom screw. Turned on water supply and reconected to electrical supply. Easier then pie.

I would never attempt an appliance repair but after watching the video instructions for installing this part I decided to give it a try even though I'm dangerous with a screwdriver. After retrieving a nutdriver from my $39 handy dandy tool set, it was a piece of cake. Upper hinge cover, hinge, door removal, comes off in a matter of minutes. Only problem surfaced when I went to install my new cam in the lower hinge. It didn't fit. It was actually for the upper door hinge. I reinstalled the lower plastic piece (whatever it's called), tightened it down, put the door back on (you can do it yourself if it's the refrig. side) and popping sound was gone. I guess the bottom hinge plastic piece was probably loose but you can't tighten it unless you remove the door. I now have a upper door cam in my drawer ready when it fails and will replace it without hesitation.

Removed the icemaker assembly, which was simple to remove. Once the assembly was removed, I unscrewed the motor housing and replaced it. I then reinstalled the assembly and closed the door. It did not making ice immediately and it took about 30 minutes to start.

Installation went fairly smooth, only problem was because it is a side by side freezer space was a little tight and screws were hard to see, but other than that works fine.

He removed the front of the motor box. He then took the motor panel off and replaced it with the new one! So easy!! We have been buying ice or getting it from a friend that has a commercial ice maker. I could not believe it was that simple and the delivery was unbelievable. I ordered the part either Thursday or Friday and FedEx delivered it Saturday! Thank you so much. Now I have all the ice I need!!!

No instructions with part. Found a picture on line and changed the arm, but it didn't fix the problem. Fairly easy after figured out what needed to be done to get to the part.

Did it entirely by myself while my husband was at work

removed the old ice maker, removed the cable from the old as none of the ones included were correct, and attached it to the new. within in two hours it was making ice.

turned the knob removed old filter, slid new filter on know and put back into fridge.

Part delivered within four days. It took all of 15 minutes to replace the icemaker after viewing the video. had a half a bucket of ice by morning thanks