Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Refrigerator light would not stay on
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced. reassembled the pieces.
Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked
Took a putty knife and Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place
Old plastic ring was damaged due to leaking icemaker causing door to open when ice dispensed.
No tool required! Pulled out tray, emptied ice into large bowl for reuse. Pushed in and pulled from inside the coil springed auger until could get old plastic ring off and put new one on. Useing care not to apply too much pressure to ice dispensing end so as not to break housing. Have to turn auger assembly at an angle to compress enough and get old ring off. Needs a little physical strenth & care not to force plastic housing to breaking point. Worked great reused saved ice. Took less than 10 minutes
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Replace the refrigerator lightbulb while traveling 88 mph then turned on the flux capacitor being carful not to get stuck in a worm hole. This allows you to fix the problem before it starts to go bad.
Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...
I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!
fountain (water & ice) switch sticks when actuated
1. Unplug refrigerator and remove fountain drip tray. 2. Remove the two #15 torx head screws that were covered by the drip tray. 3. Pull the bottom of the trim panel out and push up to remove panel and then unplug switch circuit board connector.. 4.Remove the three screws (same size as the other two) and then remove the switch, ice door, etc assembly and unplug the connector. 5. Aside. At this time I extended the water hose which has been short since new. Used a couple of inches of 1/4 inch plastic tube. Heated it with boiling water and slipped it over the existing tube to extend it about 1/2 inch. Now the water flows in a uniform predictable stream. 6.Remove the tiny phillips screw holding the switch in place. 7.Remove and replace the old switch and actuator pad and screw. Check operation of switch. I lubricated the surface between the switch actuator bar and the rubber with a little plastilube(white) grease. Probably highly optional. 8.Replace and replug the assembley. Tuck the actuator pad around the edges if needed. Remember to turn the screws CCW until they fall into the old threads and then tighten them until snug. 9.Plug in and mount trim and connect refrigerator.
Identifying the part on the parts diagram took the longest. Finding the screw driver bit that would remove the old screw that held the original shelf support took longer than the actual repair.
Once I identified the bit that would remove the screw, the rest of the repair took 5 minutes. I removed the screw and discarded the remains of the original but now broken shelf support. With the same screw I simply attached the new shelf support that I received from PartSelect.com. End of story.
I broke the crisper glass shelf while cleaning my refrigerator.
This replacement glass shelf arrived the very next day-after it was shipped. I was so impressed with the easy method of ordering and the prompt delivery of this product-also, the quality of the shelf was perfect. Great service!! I would recommend this for everything-as far as parts needed for repair or replacement.
inserted a knife between the switch and the plastic interior in order to pop the switch out. then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.