KEYE677BWH2 KitchenAid Dryer - Instructions

the heating element went on my dryer. but partselect.com had the perfect part and at a gr8t cost it saved tons of money and they are a top-notch company and if I need anything else will look at for replacement parts from this company. gr8t price, speedy delivery, best company I have found on-line..thanks for your help.. do yourself a favor and look to his company before you make a costly repair because they are the best..

just removed old fuse and installed new one ..... cleaned all the vents out to

watched the video. Removed old part, installed new one - as per video.pluged it back in and started drying clothes again!

Ordered a thermal fuse . Very fast service (24 hrs)put the fuse in and is now working again

These parts didn't fix the problem. Went to you-tube watch a video on how to repair a gas dryer step by step and which parts to replace. Found out we had replace the wrong parts and ordered the coils and now it works!!! Next time I will watch a video, first then order, this will save us time and money!

You guess that it is the heating element. They are like a light bulb, they do fail. I took the back off the dryer and removed the heater element. There is a temperature switch that needs to be removed. Examining the element, you could see a break in the element wire. That part was broken. The repair went smooth and the replacement heater assembly looked the same as the old one in design. I had to reset the dryer control and the dryer is good again.

I watched the video provided first to get an idea of how it should go. The dryer I have had a different kind of door, so those instructions didn't apply. You probably don't want to publish the way I ended up fixing it, but it did work eventually. Saved me over $500!! Thank you!

1. Opened the top. (UN-plugged it first) by prying between top and front of machine.
2. Disconnected the door switch
3. Removed two screws one each on top corners of front
4. Pulled top of front cover forward and lifted up to remove.
5. The drum will fallout if not careful, good time to remove drum to clean dust from inside machine.
6. With drum in place slide new belt, skinny side down around drum, to about halve way back.
7. While supporting drum reach back to the motor area, should be on right side facing front of machine. There you will find the belt idler/tension assembly.
8. Thread the belt through the assembly and around the motor drive pulley.
9. Ensure the tensioning assembly is firmly in the slots on floor of machine.
10. Reassemble housing in reverse order. took about 45 minutes

took the back panel off by unscrewing all the little nuts..replaced thermal fuse and put back panel and screws back on...

I watched the video to know how to change the belt. I removed the front panel and slid the belt over the tub (you will have to pick the tub up a little). Then I reached around with one hand and slid the belt over the pulley. Then I used the same one hand to push the tensioner back and slip the belt behind it. You will be doing most of the work by feeling not by vision but that's where their video is helpful. I paused the screen on my laptop where it shows how the tensioner goes around the belt. Also when you slide the belt over the tub look for the grove the previous belt left for alignment. It took me 10 minutes.

Followed your instructions. Was ready to purchase all 3 fuses or components and the lady from NS suggested would only need this Thermal Cut-Off Kit. Right on. I would and will recommend your service to anyone in need. Many Thanks

Six(6) screws were removed to separate the front and rear sections of the dryer door to get access to the rear of the catch.Pliers were used to maneuver the catch through the opening in the cabinet from the rear. The new catch was easily snapped into the catch opening from the front of the door.

I thought it might be a damaged switch but when I removed it I noticed a metal clip that was attached to it was broken. The pin on the door pushes against this clip when the door is closed which in turn opens the circuit on the switch. I looked up the model on this website and viewed the parts diagram. There I saw the part I needed and it was listed below along with the cost. Couldn't of been easier. Thanks!

Used wire schematic and locate thermal fuse. Disconnect power and remove rear panel. About 8 screws. Remove the two wires from fuse and check fuse continunity. Fuse was open and prevented power from going to gas solenoids. Replace fuse and clean exhaust ducts. Dirty ducts might have caused fused to over heat.

I went on the PartSelect site and watched some videos to determine what could be wrong. I almost guessed and bought the wrong part as there were a few. I ended up spending $17 for a multi tester. Once I determined that the thermal fuse was bad. I just followed the instructions from the video and replaced it. Took me more time figuring out what part was bad and buying the tester than actually replacing the part. Very glad I bought the multi tester watched the videos. After that it was easy.