KERC600EWH5 KitchenAid Range - Instructions

removed the worn out roller...inserted the new roller....tightened the nut...it was finished...this was without a doubt the most pleasent repair from start to finish..only took 3 days from the time i orderded the part to completing the repair...i would advise anyone to use " partselect.com" without hesitation

removed back of stove, removed 2 screws holding element, disconnected element and removed it, then reversed procedure. excellent service from part select and will use them again when needed.

In my situation, removing the control panel first required pulling the range unit forward to expose the side screws, which first required removing the screws holding down the stove (tilt prevention. Those screws are accessed by removing the bottom range drawer). Replacing the switch was a breeze. Very important to label wires before removing them from the old switch. Also, over the years, food liquids that spilled on the range top "gunked up" the front gasket seal of the control panel. Suggest cleaning the gasket as part of the repair - something a DIY should always do! Leave it better than you found it. When I removed the current switch, I could tell by looking at the LED terminal post there were burn marks which suggested there was indeed a fault in it. For about $45 I replaced a switch that would have cost over $200 for a repair person to come.

lift oven door off of stove lay on towel on floor unscrew bottom screws,two(2)top screws remove oven glass face remove interior metal panel, lift fiberglass out,remove five(5)screws lift out outer& inner glass frame,romove broken glass, lay in new glass. Then reverse directions. NOT BAD AT ALL>

Had already removed back covers and disconntedted power. When io received parts I replaced them in reverse oder I had removed them. Took me longer to replace back covers because of my bad diabetic hands. Thanks very much, yopu savbed me a bunch. God bless you and yours, god bless america.

Moved stove away from wall, cleaned ( hadn't been moved in 17 years). Disconnected Dual Broil Element, replaced with a new one, stove worked fine.

I tried taking the sensor out, but the plastic coupling behind the oven wall had melted and the melted piece was larger than the opening in the oven wall. I had to use a mini-screwdriver to chip away at the melted coupling before it would fit through the opening. That took forever...but it finally worked and the repair went quickly (15 minutes) after that.

Removed broken glass cover and bulb, cleaned old gasket off with damp cloth and replaced with new bulb, glass cover and gasket. No tools needed.

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

I live in a small town in South East Colorado. We have just a Walmart and Sears and a few smaller hardware stores. I checked all of them to try to find this 25 1/2 inch Fluorescent Light Bulb, and nobody carried one. I would have had to drive 70 miles to find one. The Service of Partselect was wonderful and the bulb showed up in just 4 days. I was lost without this light. I have bought a few other items for my older appliances in the past from Partselect. com and was very happy with the service and how easy the web page is to navigate. .

Repair was very straightforward. Based on information gathered from an earlier post about the same repair I simply removed all screws from the oven door. These were all located on the bottom edge of the door itself. Upon removal of the screws the door separated and exposed the "core" where I then had access to the hinges which were held in by one screw each. I removed the broken hinge, replaced it with the new hinge, pieced the door back together, put back all the screws, and the repair was complete.

finally figured it out , but instruction sheet could have shown old switch terminals & new switch terminal locations.

Unscrewed about 10 screws to disassemble the door to get at the hinge then screw new hinge in. Was inspired by the woman who said she did it while watching a child. I saved $200 in the repair fee I was quoted

1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilitate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.