Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JVM1339BW02 > Instructions

JVM1339BW02 General Electric Microwave - Instructions

All installation instructions for JVM1339BW02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JVM1339BW02
91-105 of 239
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Under the microwave there are two light bulbs that light up the top of the oven/range.

  • Customer: Janet from TREASURE IS, FL
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Last week I removed the glass cover that was held in by one screw and removed the burnt out light bulb. I ordered the bulb and left the glass cover off until the bulb arrived. I had to wait until this evening to put the glass cover back on and fasten the screw because I have a window right next to the oven and the sun streaming in made it too difficult for me to see how to put the glass back in and replace the screw.

Glass lens and two light bulbs replacements

  • Customer: Linda from SEASIDE, CA
  • Difficulty: Very Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
My microwave is built in above the stove which provides lighting and fans for my stove. The glass lens cover for the lighting was cracked in several places and the light bulbs had burned out. I taped the glass lens for removal so it didn't break apart due to the cracks Removed the one screw. .Both light bulbs broke away from the base sockets as I tried to unscrew them. I used electrical tape wrapping in reverse on a lightbulb (socket end) so it was sticky for a grip on the base, shoved it in the sockets and was unable to unscrew the broke off bases. So it was very successful and no repair man was needed.

When you open the door at the start the fan wood come on

  • Customer: Larry from CHARLOTTE, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
I removed the unit from the wall removed the top two screws holding the panel above the door I the two screws holding the control panel removed the three switchs I found the top one to be blown and replaced it

Microwave will not start

  • Customer: Carlos from GLENDALE, NY
  • Difficulty: Very Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
Removed three screws from the top front cover and slide it out and following I removed the touch panel and the housing that holds the switches and replaced the bad one.

Bulb broke in socket, socket had deteriorated beyond repair.

  • Customer: Frank from CICERO, IL
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Phillips screws on bottom panel allowed me to install new socket and put electric connection back. Secured bottom panel and that was it.

Both under mount lights were burned out

  • Customer: Divina from Grand Rapids, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Unscrewed bottom panel, then unscrewed light socket, then replaced with new socket and bulb. Reattached socket and panel.

Remove old light sockets and replace in Microwave over stove

  • Customer: Cathy from LINCOLN, CA
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Have a microwave that the light and sockets just broke in pieces so I ordered two sockets from this site . The fit perfectly and it was a breeze to install. Took out 7 screws and the plate dropped down, hooked up the little wire which was so simple and bingo I had lite again. I just wished the hold plate came down but it didn't but it was still very easy to install. Will continue to get my appliance parts from this company.

bulb burned out light that is under the microwave, which lights the oven below.

  • Customer: Gary from UNIVERSITY PA, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
thank you for the video--very clear, responsible, applicable although the illustration was not exactly of our kind of light. the bulb was exactly like the one Hotpoint used in its microwave made in 1989! I will come back to you for parts in the future. (You have the model # from my original order.)

Left light inoperable

  • Customer: Paul from TULSA, OK
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
Ordered and received two parts. Price was exceedingly high. $13.34 for a simple light socket and $7.05 for a 40W light bulb. The ;light bulb was received with a broken filament so was useless. Went to a local bulb show and bought a new bulb at a fourth of the cost of the Part Select website. As fpr installation, to reach the old bulb, had to take off the bottom of the microwave. Replaced the socket with the new one and put in the new bulb. Everything OK now.

Door handle broke

  • Customer: Eduardo from San Antonio, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
unscrewed the old handle and screwed the new one on really quick.

Broken lens

  • Customer: Norman from Voorheesville, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
remove two screws bend out flaps remove broken glass install new glas bend flaps back to hold glass install two screws. Done.

Previoous glass lens was broken

  • Customer: Tommy from Santa clarita, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
This repair was easy and could be done by anyone. If you undertake to do this replacement, remember to slowly bend the medal tabs back that hold the lens. Handled roughly these tabs could break off.

This repair can be don in under 5 minutes, easily !!

Right hand surface lamp burned out. It apparently fald up and broke the glass cover. I wne on line when I found out the only local deaaler was some miles away and more expensive.

  • Customer: Leon F. from Brookline, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Simple. The parts came instantly. The glass was too big so I had it cut to size. I unscrewed the fixture with a screw driver replaced the bulb and slipped the glass cover into the frame and screwed the whole assembly in.

bulb burned out -cracked holder lamp

  • Customer: Terry from Justice, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
pluged wires back on ,placed lamp holder and bulb back and replaced screws

Cheap plastic handle on microwave broke again

  • Customer: John from Yorktown Heights, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Open the microwave door. Remove the exposed screw in the top left hand corner. Using a knife, pop off the plastic moulding that surrounds the glass out to expose the screw in the bottom left hand corner of the door. Remove that screw. (note they are two different types and lengths). Attache the handle and screw in the top screw, then the bottom screw. Re-attache the moulding around the glass. Close the door and reopen with new handle.
All Instructions for the JVM1339BW02
91-105 of 239