JMW8530DAB Jenn-Air Microwave Oven Combo - Instructions

Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.

Access is via RT. SIDE Panel as you face microwave. There are three screws on the bottom right edge to loosen. After that the side panel slips down and off. the fuse is located in the rear near where the power cord comes in. It is the white ceramic tube 1/4" in dia. and 1-1/2" long. Pull it out like any fuse and replace with new one. Reassemble and you are done!

ordered a new tray

Door fell off so removal of door was easy. Removed screws holding the door together to expose hinges. Removed old hinges that were 3 screws for each hinge. Placed new hinges and installed screws then put door halves back together installed screws and then finally replaced door onto the stove. Mission accomplished

Watched a you tube video prior to installing new switch. Followed the video which gave me confidence i was up to the task. After removing the touch pad I found my design was not exactly like the you tube model but I found the defective switch, replaced it and put the microwave back together. Works great. Again watch the videos

I took the broiler pan out of the shipping container and put it in the oven.

Required that i remove the built in frame and mounting. Required tamper proof socket to remove housing. I removed the old bulb and simply replaced and reverse installed the cabinet.

First I removed the oven door - with door fully open pull the clips on the hinges all the way out, then close door as far as it will go and lift the door up and off the oven.

Then I removed the three screws on each side, that hold the oven to the wooden cabinet. I then slid the oven unit out from the cabinet about 6 inches, to gain access to the hinge receptacles.

I then removed the 2 screws that secure the receptables to the oven body, and replaced the receptacles.

Reverse steps to put it back together.

Works like a charm.

I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.

After watching a you tube video or two, I easily detached the oven door. One of the hinges was jammed, and upon releasing it with a screwdriver, it snapped open and gashed my thumb. This as entirely my fault, I did not realize how much force was held in the spring.... You must remove the bottom frame piece and inside door pan to get to the hinges. All Phillips head screws, and all the same size. Once these are removed the hinges are easily removed with 3 Phillips head screws. While l was this far into it I removed the two layers of glass to clean them on both sides. This requires a small nut driver to remove the channels holding the glass. There are three layers of glass to clean on both sides, quite dirty and brown. Reassembled the whole thing. The door assembly popped right back in, and now functions like new. You can actually see into the oven, without opening the door!

Rotated the hinge lock with a screwdriver, pulled door off hinge bracket, later door on table, removed screws to detach inner door frame from outer door. Three screws to remove each hinge. Very easy.

Pulled the double wall oven out about five inches and install replacement brackets on both sides. Reinstalled oven doors and slide ovens back. Piece of cake— the lower oven door closes better than when oven was installed 13 years ago. Believe I had a bracket problem from day one!

Replace the racks. No special instructions.

Removed the original rack. Checked dimensions, installed the new rack.

This was easy to replace. I removed the oven door for easier access to the back of the oven. Removed two Phillips head screws that hold the burner element and disconnected the two wires on the burner element. I could have left the wires connected, but it was easier to extract the sensor with it out of the way. The only difficulty was fishing the sensor connector out through the hole. After that, easy peezy.