Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
runs but does not heat
I removed the main cover ( torx security bit required) and tested the magnetron, capacitor, diode and door interlock switches according to instructions found on the internet. The capacitor and diode tested good but the magnetron looked burnt and corroded on the tip. The magnetron I received was an exact replacement for the original. It was easy to replace the magnetron which arrived in 2 days standard shipping. I also cleaned the fan while I had access to the inside area. Hoping to get another 18 years use from the microwave!
Frost build up on bottom to ice bin and delivery chute in door creating ice blockage
Remove the ice bin. Turn the ice maker selection to "OFF" Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one. Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug) Move the selector from "OFF" to "ON" Replace the ice bin and close the freezer door
Very easy to replace. This replacement part is the perfect fit for my microwave since the original part has been discontinued. It does have the night light and bright light feature.
-unplug -remove top and front covers -unplug wire connectors from heating assembly -remove heating assembly from metal stand and push out of the way -remove metal stand from dry -pull out heating assembly -install new one in reserve order
Door Switch went bad, Internal Fan would run every time you open the door
Unscrewed the control panel (2 screws), lift up and let hang, with a plan screwdriver open bracket holding the switch, unplug 2 wires, replace with new switch, plug in the 2 wires, push switch back into bracket. Then slide on the control panel, put the 2 screws back. Easy fix.
First I had to accept the fact that the unit was designed to keep non-professional people from doing any repairs. The switch was installed in such a manner that I had to break the mounting to remove the switch, then drill a hole in the mounting to secure the new switch in place.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Turntable motor was making noise
Unscrewed and dropped the bottom panel of the Advantium on its rear hinge, disconnected the light and the motor, removed the motor screws, and replaced the motor. Very simple. However, not related to the Advantium or the motor, trim had been applied to the bottom of the wall cabinets after installation of the Advantium. This trim prevented the lowering of the panel (and future removal of the whole oven), so I had to chisel and file and repaint the trim to get it out of the way.
Turntable Stopped Working/Display Timer Would Countdown But Not Heat
With this model, you must remove the outer covering. Don't try to access the display unit from the front like I've seen in some other GE microwave videos. After removing the outer covering, the switches are easy to replace. They are very visible and easy to get to without taking any other parts off. You will see the door switches just behind the display board. Remove the switch and then remove the connecting wires to ensure you don't inadvertently brake a wire. You will need a tamper resistant star bit to remove 3 or 4 screws from the back panel. All other screws are philips head. I went ahead and replaced both switches (yes...there are two of them) and works like a charm. I saved an $800 microwave for less than $60 and know what to do if it happens again. Appears to be a common problem on this model. Thanks for others making a post...It saved me time and money reading others remarks. Good luck!
Microwave not turning on. All other functions operate
DISCONNECT THE POWER CORD and discharge the capacitor Leave unplugged overnight Remove vent grille by removing the 2 philips screws Remove the LED panel by removing 1 phillips screw Disconnect all connectors that plug into back of the LED board completely Remove the wires from the switches (3) at the inside edge of the microwave door Gently remove each switch housing and test all three switches for continuity Carefully replace non-functioning switches and reassemble the panel GOOD LUCK
Part Select sent the wrong part I did not realize it until prong broke off one of the bulbs. They sent 130v instead of 120v. Return bulbs awaiting resolution.
