JGBS23DEM2BB General Electric Range - Instructions

First I needed the correct model number & the correct part numbers for the two front tube assemblies. After that well.... I removed everything on top of the stove. I then proceded to remove all the torx screws for each orifice holder bracket & igniter wires so i could raise the top lid ( without this step you will wind up replacing more than one tube assembly!) Be careful when removing color coded wires so that they work with the correct burner. Remove compression nut to burner valve... i used a crowfoot. remove orifice holder from bracket & install new holder ( onto bracket). Install orifice assembly to burner valve ( do not over tighten), re-install wires to igniters, lower lid, and re-install torx screws. The correct parts require little effort to align. Last of all, test burners and check for leaks. Thanks for reading, I will continue to learn from my mistakes!

Really self explanatory. Removed the old drip pans and put in the new. No tools required. However, I would like to say I received the parts the day after I ordered them. EXTREMELY FAST SHIPPING!!

Removed the two screws put the heat shield off the old one onto the new one put new bottom in and tightened two screws. Done #38. 69 Cost of part with shipping cost included.

I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

remove all loose components on range top (grates, caps, disbursement / diffuser heads. Take a T-15 screw driver and unscrew each of the three screws on each burner. Have a large flat headed screwdriver ready. Lift up on the front lid of the range, it should life about 1/4 inch. There are two clips that hold it down, about 6 - 8 inches in from either side. Press then towards the back (away from you) one at a time, while lifting on the lid.. it should pop free. WARNING: if you did not remove the torx screws first, be careful are you will now bend the gas lines running to the burner. Once loose, remove the old clip from the igniter, so that it lifts free. unplug the igniter from the electrical cable (pulls out from bottom). attach new clip to new igniter and re-attach electrical line to new igniter. close lid and re-attach all torx screws. Reassemble range top and you are complete.

determined that the top of the burner was melted and malformed. Repair was simple: lifted off the damaged burner and slipped the new one in place.

the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino

removed two screws and took out bottom tray and put the new one in and replaced the screws.DId it my self.

We made a good choice ordering the part on line it was easy to fix save us a lot of money . Thanks a bunch! I would definitely order again on line if need . Very pleased

Not a repair - just a replacement. Very easy. Just remove the grates, lift out the drip pans, replace with the new drip pans, and replace the grates. As the size of the holes vary you just have to make sure that they are lined up correctly. I was delighted to find that replacements were available for a range I've had for 14 years. The range itself still works great. Thank you for your promptness in sending the replacements. I highly recommend your service.

Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver

Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.