Models > JGBS21HEH5WW > Instructions

JGBS21HEH5WW General Electric Range - Instructions

All Instructions for the JGBS21HEH5WW
16 - 30 of 89
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Needed extra oven space
Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.
Parts Used:
Oven Rack
  • noreen from flushing, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
11 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven post mini explosion sounding
the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino
Parts Used:
DEFLECTOR OVEN
  • Mchael J. from Chesterfield, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
13 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Igniter no longer worked
remove all loose components on range top (grates, caps, disbursement / diffuser heads. Take a T-15 screw driver and unscrew each of the three screws on each burner. Have a large flat headed screwdriver ready. Lift up on the front lid of the range, it should life about 1/4 inch. There are two clips that hold it down, about 6 - 8 inches in from either side. Press then towards the back (away from you) one at a time, while lifting on the lid.. it should pop free. WARNING: if you did not remove the torx screws first, be careful are you will now bend the gas lines running to the burner. Once loose, remove the old clip from the igniter, so that it lifts free. unplug the igniter from the electrical cable (pulls out from bottom). attach new clip to new igniter and re-attach electrical line to new igniter. close lid and re-attach all torx screws. Reassemble range top and you are complete.
Parts Used:
ELECTRODE TOP Top Electrode Mounting Clip
  • BRAD from Halethorpe, MD
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
13 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven bottom tray would not clean up.Looked like finish was off it
removed two screws and took out bottom tray and put the new one in and replaced the screws.DId it my self.
Parts Used:
BOTTOM OVEN AND DEFLECTOR ASM
  • Jim from 29 Palms, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
11 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
loss of spark to two burners, and bent orifice holder
unplugged the old spark module and plugged the new one in. Disassebled and reassembled the new orifice holder.
Parts Used:
Left Front Orifice SPARK MODULE REPLACEMENT KIT
  • Kimberly from Leavittsburg, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers, Wrench set
12 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
one burner would not light
opened back panel. noted location of colored wires. disconnected wires & removed module. attache wires to new module & attached module to panel. closed up back panel. tested all burners
Parts Used:
SPARK MODULE REPLACEMENT KIT
  • joe from malden, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
7 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hole burned through deflector oven and metal dropped onto igniter and burned it out
Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver
Parts Used:
DEFLECTOR OVEN
  • Scott from ARDMORE, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burnt burner
Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.
Parts Used:
Burner Head - Medium - 9500
  • Janine from Wind Gap, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
7 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not turn off due to inoperative thermostat
1st ensure thermostat is intact, I thought it was broken but upon further investigation I noticed that one of the screws that hold the thermostat in place had came loose which cause the thermostat knob not to be able to turn the thermostat stem. Re-installed thermostat mounting screw and it worked just fine.
Parts Used:
Oven Thermostat
  • Timothy from Lake Elsinore, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
7 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old blackened oven racks
Replaced old with new.
Parts Used:
Oven Rack
  • Roger from Falls Church, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
8 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner on stove not working correctly
Order parts and installed - no tools needed - completed repairs less than 1 minute
Parts Used:
Burner Head - Medium - 9500
  • Trevor from Eldersburg, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lights blown out
replaced lights in refrigirator and freezer
Parts Used:
Light Bulb - 40W
  • Gerald from WINTERVILLE, GA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
6 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken lines
Super easy!
Parts Used:
Right Front Orifice Left Front Orifice
  • David from BONSALL, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven ,Going on/off intermittently" Very Dangerous during day /at night especially when all is asleep /away from home,not knowing!
To: Remove.Four(4)nuts. Six(6)screws. Two (2) clips. To:Reinstall reverse process. "Very simple stright forward, and most enjoyable."
Parts Used:
Oven Thermostat
  • Leroy-Anthony from Jamaica, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
none
slid the old ones out and slid the new ones in. done
Parts Used:
Oven Rack
  • Michael from Laughlin, NV
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JGBS21HEH5WW
16 - 30 of 89
Back to Top