Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ignitor burned out and would not allow oven to heat
This oven is from 1993 and a lot less complicated than today's models probably are. The first things to do are to remove the oven door and broiler pan. On this model, the oven door simply lifts off the hinges. Once these are gone, you want to remove the oven floor. To remove, locate the two screws at the back of the floor. After removing, lift the floor up and towards the back to pull the floor tongue out of the groove in the front. This will expose the gas jet and ignitor assembly. At the front of the jet pipe is a screw that holds the pipe to the front center of the frame - it is underneath so you may have to bend over to see it, it can be felt easily as well. Remove this screw, this will allow the pipe to be moved a little later. In front of the assembly is a vertical metal plate with a screw at the right of the mounting the plate into the broiler floor. Remove the screw and slide the plate to the left to pull out another tongue/groove set-up. Now you should see the wires completely and the connection to the air-flow adjuster. There is a small screw in the front of this brass fitting, it does not need to be touched. Turn the burner pipe clockwise while lifting and this should pop the assembly up. The ignitor is mounted to the burner pipe by 2 screws that are found on the bottom of the mount. Remove the 2 screws, this will allow the ignitor to hang free. Be sure to pay attention to what wire attaches to what wire, I marked the left wire so that I knew which to reconnect to after the change over. Remove the caps on the wires if this unit has been removed before, if not then mark the wires on both the replacement unit and the original wires. My ignitor has been replaced before, so I used my wire cutter to clean-up the ends of the old connection before reconnecting the new replacement. At this point, you should be able to fire-up the oven, it might take a moment for the new one to warm up, so give about 30-40 seconds. If the oven fires up, it's then working to put everything into place in reverse order. I like to line up the parts and pieces as I remove so I can just put back in reverse.
Removed spark module only two small nuts. Inside was six wires on terminal. Removed one by one and connected right to the new module. Easy job 10 minutes and finished.
Removed oven base plate by removing 2 screws and lifting out of oven. Pulled out bottom drawer and disconnected two wires from igniter. Removed 2 screws connecting burner to oven wall. Back to oven inside, and removed screw holding burner to oven bottom. Took burner out if oven. Removed 2 screws securing igniter to burner. Secured new igniter to burner. Reversed steps to put all parts back. Oven works fine.
1. Removed oven door. 2. Removed shelves. 3. Removed oven bottom. 4. Removed pan drawer. 5. Removed the 2 burner mounting nuts at back of oven pan drawer opening. 6. Removed top burner nut. 7. Pulled igniter out from top. 8. Snipped igniter wires. 9. Removed igniter from burner 10. Attached new ignitor wires with the enclosed wire nuts. 11. Attached new igniter to burner. 12. Replaced burner. 13. Pushed excess wire out of the oven through opening at back of pan drawer. 14. Reinstalled burner mounting nuts at back of drawer. 15. Reinstalled burner nut at top of burner 16. Reinstalled oven bottom, oven door and pan drawer.
Replace Oven light socket and light bulb in kitchen Range
1) Turn off power at circuit breaker panel 2) Slide out Range from wall 3) Unplug Range 4) Remove back panel and unplug electrical connections to socket 5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb 6) Remove old socket from mounting flange and discard. 7) Place new socket into mounting flange 8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back. 9) Screw in new light bulb from front 10) Replace existing glass cover over new light bulb and snap wire holder in place 11) Replace back panel 11) Plug in range 12) Slide range back to original position 13) Turn on power Works like a charm! Thanks for having the parts after 30 years!
Very simple repair, removed the back plate, took off the 4 screws holding the controler panel on, swapped over the wires one at a time, and reinstalled. Less than 15 min total time.
bought new panel and installed and looking @ wire connections from old control, I'm very much mechanically inclined , so was a breeze for me, but non handy people may not know how to disassemble the control panel without not having an idea how it's made. I'm a "mr fix it", "jack of all trades" kinda guy and am proud of it.
Removed oven door, warming drawer, oven bottom, oven burner, disconnected wires to igniter. Also, instructions said to turn off gas supply at pressure regulator, {little red lever.} I also turned off main gas supply, and un-plugged power cord. Removing the igniter and replacing with new one was easy. Splicing wires and putting everything back together was also pretty easy. The only problem was when I tryed to open the gas to the pressure regulator, the little red lever popped off. Very cramped area to work in, could'nt get a tool to fit in there. So, I got some nylon string, made a loop, looped it on the notch on the pin, pulled it out and got the little red lever back onto the pin and then was able to open the valve. There is no gas going to the burner if that lever is not on holding the pin out, and you can't put that lever back on unless the pin is pulled out. If I ever do that job again I will not touch the red lever, I will just shut off the main gas supply. It would have been a pretty easy fix if that lever would not have popped off.
I was so sick of this drawer and I over heard a buddy telling a story about a website that you can get ANY piece for appliances. I take the drawer out, look up the website (partselect.com) look at the appliance diagram and find the missing piece. Order it, get it, install it. My wife thinks I'm a hero and I think I'm pretty cool too.
The part was very easy to switch out but it made no difference whatsoever so I returned it. The way it is designed is the problem. There is a pie slice shaped gap on the burner which causes a gap of no flame. Also a C shaped cut out around the igniter which causes another no flame gap.
Unplugged the electrical.Removed the door, removed the oven racks and removed the bottom pan. Removed the wire nuts from the two wires. Removed the burner tube. Removed the Igniter. Installed in reverse order. It was very easy however it was the third igniter that I had to replace in this range so I was used to it.
