Enter the code TAKE10OFF at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on May 28 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
stove top burner ignition spark progressively got weaker and then stopped on all but one burner.
I located the igniter module by following the wires to the top/rear of the stove. Removed two sheet metal guards and marked and numbered each electrical wire before removing them. Reasembled in reverse order. Wife thinks I'm a genius!
I specifically asked if $16 plus would be the sole expense for this item. I was told that it would be plus there would be no cost for return of the rubber feet. Several hours later I was emailed an invoice that the cost would be $26 plus for four rubber grill screw-like items, a vastly over-priced item. I called and learned through the email system that the item had not been shipped. I requested cancellation at 5AM Saturday. Friday night order led to Saturday morning cancellation -- and Monday morning delivery despite my specific request to cancel. I am not satisfied. It seems like I have been hustled.
This was a real easy repair. The key is to remove the door (by lifting straight up) and remove the bottom drawer. Then take all the trays out of the oven, using a screw driver remove the bottom pan that hides the burner and igniter. From underneath the oven (ie drawer space) use a screw driver to disconnect two screws that hold the burner assembly against the back wall of the oven. Then remove the one screw from inside the oven that holds the burner assembly (its close to the door area). Unplug the two igniter wires from underneath the oven and then lift out the entire burner assembly. Take off the two screws that hold the old igniter to the burner and replace with new igniter. Make sure you mark the wires when you remove them because you need the connectors on the end for the new wire. Then give yourself plenty of wire, cut the old wire off the old igniter and using the provided wire ties join them to the new igniter wires and reconnect everything. Sounds complicated but it took me about 20 minutes and its really an easy repair. Good luck.
I was a bit hesitant to perform this repair but attempted it due to the other write-ups which were very helpful. The repair went very well and was quite easy. There was a suggestion to remove the gas defuser (the pipe thing that has the igniter attached), I believe loosening this defuser made the whole repair so much easer and quicker. Trying to remove the two screws that hold the igniter without this approach would have been very difficult. I was hesitant to do this but removing the 3 screws that hold the defuser in place was not a problem at all.
Simple swap and go.Several wires had different locations but every thing was marked well on both panels.Did one wire at a time.Took about 45min from pulling out oven to pushing back in.Just wish I had known about your site years ago.
Very easy install of done correctly. When you pull range out,watch the gas line and don't pull it out of it's fittings. Two small Phillips head screws on the front panel low to the sides. Then two 5/16 screws on the top back panel and flip it forward. Rest it on the stove and the control panel is facing you. I'm a 30 year Electrician so please take my advice and make a schematic of the wire colors and the NUMBER associated with that color wire. Once that is done remove all wires and also a green ground wire that is under a screw. The new panel may NOT have the exact same configuration but the NUMBER on the terminals will be the same. Plus all color wires to the appropriate terminals and reinstall !! Great job!!
Gas range igniter was making a clicking sound every 3 to 5 minutes, as if it was trying to ignite one of the burners.
Unplug the range from its wall socket to avoid electric shock. The various range parts that support a pot or frypan are easily lifted off their perches, exposing the small white igniter. The only moderately difficult aspect is wiggling the igniter out of its retainer. The electric wire leading into it then can be pulled out and fed into the new igniter with a push. Replace igniter in its retainer, then replace the range parts you removed to expose the igniter and plug the range back into the wall socket. Piece of cake.
