All Installation Instructions for General Electric Range JGB850SEF1SS

Replace temp sensor in gas range

Part came as ordered. Hardest part was fitting plastic wiring harness through the hole with 2 layers of steel with insulation in between. Used electrical tape to stiffen the end about an inch or 2 back from harness. Job done, problem solved

Parts Used:

Range Oven Temperature Sensor

Ron from PAINESVILLE, OH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner cap wasn't working proper.

took burner off installed new one thank you for fast shipping

Parts Used:

Burner Cap

GLENN from ST CLR SHORES, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Food ran over the burner and damaged it.It was easy to place it back inII

It only required placing the new burner in the proper location.

Parts Used:

Burner Cap - Black - Medium - 9500 BTU

Alan from PASADENA, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Wrong parts

Your diagram on your website says lower oven is incorrect everything on there is upper oven I ordered the wrong part because your diagrams are all wrong OK

Parts Used:

BAKE DEFLECTOR UC

AMON from MARYSVILLE, CA
Difficulty Level:
Very Difficult
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

shortage in wiring cause the housing to burn out

Replaced new light housing.
Thanks to you guys for the prompt response

Parts Used:

Oven Light Housing

fred from PALM COAST, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner cap replacement

I got really great customer service on finally getting the right part. It came really fast it fit perfect but the cap is a high gloss black instead of a flat black. I will need to call customer service again to see if they can the correct color this time.
Otherwise everything was great!

Parts Used:

Burner Cap

Rita from ST AUGUSTINE, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

gas burners not heating evenly

remove old burner, put new in place

Parts Used:

Small Burner - 5K

Burner Head - Large - 12K

Burner Head - Medium - 9500

Juanita from GAINESVILLE, GA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

flame was inconsistent. too much air.

replaced old with new.

Parts Used:

Vision Burner - Extra Large

Raymond J. from EASTPORT, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced

the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.

Parts Used:

Top Electrode Mounting Clip

Dana from LEEDS, AL
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bottom portion of range would not heat up.

Called sears

Parts Used:

IGNITER GLOW BAR

Patricia from WESTERVILLE, OH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Part does not look like the part that needs to be replaced

I have no clue what wire goes where because there is no thing to refer to or instructions of any kind . I have not been able to install the part.

Parts Used:

SPARK MODULE 6+0 KIT

P from FULLERTON, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven sensor not working

Very very simple repair!!!!! Works great!!

Parts Used:

Range Oven Temperature Sensor

Mary from TUCSON, AZ
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Gas Oven will not light

I was disappointed with this parts recommendation..neither part solved the problem, a first with partselect. The Range Oven sensor change out was easy and straight forward once the back lower panel was removed. The SPARK MODULE was time consuming..the module is located and accessible only by removing the range top. Having gas burners requires unscrewing all the burners before tipping up the top and removing it, then removing the guard over the Module is next..it's a project, sure wish it worked when I was done!..turned out to be the oven glow bar....

Parts Used:

SPARK MODULE 6+0 KIT

Range Oven Temperature Sensor