JES9800AAB Jenn-Air Range - Instructions

Turned off Power to oven, flipped breaker. Unscrewed two screws, removed old burner, inserted new burner, screwed in. Turned breaker back on.

Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.

Very easy repair, just remember when you pull the heating element out of the oven, to do it slowly and carefully, as the wire connecter just slides on and off. The Oven light replacement bulb for this Jenn-air unit DID NOT WORK. I got a refund from Partselect, and replaced it with a bulb from Lowe's. Thanks Partselect for making this so easy!

I watched the video, which was very helpful...the temperature sensor was hard to pull through the small opening in the upper back left oven corner. On the back wall of the oven was a large removable circle, so I unscrewed that piece and was able to gain access to the wires attached to the temperature sensor and push it through the small opening. I used one of the new connectors, pushed it back through the small opening, screwed it back onto the oven wall, replaced the circle opening and tried the oven again...unfortunately, there was no improvement in oven temperature! My JennAir wall oven is about 17 years old, and I thought I would try this $30 repair prior to purchasing a new wall oven, but it looks like I will have to do some overtime and buy a new oven. Any other suggestions would be welcome.

Followed video

Turned off power, disconnected wires, cut tape on exhaust fan connection, removed cooktop from counter and removed glass top from assembly, removed screws on switch, switched wires from old switch and installed on new switch, reinstalled everything, restore power and checkout new switch positions. Everything worked.

The dual burner on my range wasn't working—the inner, smaller portion would heat up, but the outer portion (for larger pots/pans) would not. I searched online and discovered that the element is easily replaced, and Yay! It was! I had difficulty finding the model number of my range, as it wasn't in any of the obvious, suggested places. I had to get help to slide my range away from the wall (which was the most difficult part of this project!), but in doing so, found a metal tab on the back of the range, near the top, that flipped up to reveal the model and serial #s! From that info, I was able to find and order the correct replacement element for the burner that wasn't working, and in less than an hour, had it fixed!

Powered off circuit at breaker switch, removed oven door (slide-in), unscrewed two Phillips head screws holding old element, unplugged old element, plugged in new element, screwed in new element, replaced oven door and turned-on circuit. Total repair time: 8 minutes. Total time procrastinating repair: 1 week. Happy Wife: Priceless.

Lifted the old one out and put the new one in. Very easy

Turned off breaker,opened door with bent coat hanger by sliding right to left the coat hanger to open the door, remover 2 screws holding in the sensor in upper left corner of the oven. Remove the sensor (gently) with the wire connection from back of oven pulling sensor out a out 8 inches . Disconnect plug. Install new sensor with matched harness /.connection, installed 2 screws ,turned on breaker.

used screw driver to remove two screws gently pulled element out to expose wires. Removed wires from old element replaced wires on new element gently pushed element in to place replaced screws. Job done very easy.

The repairs was really easy. All you had to do was remove the screws holding the glass top surface down, raise it up, then start by pulling one wire at the time and plugging it into the new element. Then bolt the glass top surface down and it was ready to use, good as new.

I replaced the oven sensor which was easy to replace. A pigtail wire was provided with the sensor which is intended to be installed first so you don't have to reach around the front and back of the oven at the same time. The replacement was easy. However, that turned out not to be the problem. The real problem was the maytag electronic clock control timer, temperature control unit. The part number is 7601P177-60. This device has been discontinued and I was fortunate enough to find the part at a local supplier. Once I replaced this, the problem went away. The oven heats up normally. My original symptom was that when setting the oven temperature to something like 350 degrees, the display would rapidly report heating up the oven to that temperature, and the oven was only mildly warm. If you have that symptom, it is probably not the oven sensor. It is the electronic clock unit. Hope you can find one. If you can't, I think you need to by a new oven. Regards

The video you provided was excellent! Turned the circuit breaker off. Removed four screws, pulled out control panel, took a picture of the wiring to be safe. Disconnected the wires from the damaged control and removed it (two screws removed). Mounted the new control, connected the wiring, replaced the control panel and the four screws. Circuit breaker back on, turn burner on. That's it. Thanks for the video!

Removed the two screws, on both sides of the oven wall corner. Gently lift the front end of the glass top and pull towards me and disconnect the two electrical sockets. Carried the glass top assembly on the kitchen table and turned upside down. Removed the six screws. Removed the assembly from the glass top. Turn the top burners assembly over and disengaged the two clips of the burned out burner from the assembly plate. Transferred the two clips to the new burner on the exact locations like the old ones were. I have placed the new burner on the location and snapped the clips on the slots. Removed the connectors one piece at a time and connected to the new burner. Reversed the previous disassembly and all was done Works like a charm. Thank you all for assisting me in providing the necessary parts and video instructions. It was a lot cheaper than to buy a new range.