Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The old motor wouldn't turn the fan.
After moving the refrigerator away from the wall I removed the cover on the lower back of the unit by removing the screws that held it in place. The condenser fan was not turning and there was heat build up in the area causing the refrigerator to not work properly creating elevated temperatures in both the freezer and regrigerator. Removal of three torx screws from the original motor was all it took to get the motor free. By turining it and working the fan blade around the mounting bracket I had the motor out in just a few minutes. Replacing the new motor was just as easy to reinstall. The fan was removed from the old motor and placed on the new for installation. The original motor was wired to accept a connector from the wiring harness of the refrigerator. I simply cut the connector off the wiring harness and stripped the insulation from the wires which easily allowed me to connet the wires of the motor and harness with two wire nuts. Three self tapping screws were used to hold the motor in place replacing the torx screws. Installed I plugged the unit in and immediately the fan started spinning as the unit came to life. Cleaned and replaced the cover over the back and slid back into its spot. Running as good as it did when it was new. Easy job to take care of.
I was about to waste $1000 on buying a Refrigerator. Took 1 mins to search on google "Refrigerator doesn't work". Found a video on youtube, showed a step and step video to solve my problem. Order the part $50 and it took me less then 5 mins to install it. =)
The new Ice Maker Assembly arived in less than 24 hours. I was amazed that it came so fast.
I had already removed the old ice maker in order to get the modle number.
I just took two parts off of the old ice maker and quickly snapped them into place on the new ice maker. Then attached it to the refrigerator in less than 10 minutes. With in a few hours I had ice again !!!!!
Vegetables kept freezing regardless of temp setting.
I noticed that the thin plastic flap was missing. I squeezed the housing, unsnapped and pulled. INstalling the new part was just the reverse. No more frozen vegetables.
Defrosted coils with hair drier and after the freezer was turned back on the freezer cooled to 0 Deg. within 4 hours but coils collocted ice. Checked coil with ohmmeter OK replaced Defrost Assy. Repair was very easy and new replacment unit is sealed and the original is an open curcuit board. thanks for allowing me to share this with you!
tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok
This is the 2nd time I replaced the ADC, the freezer condenser was frosting up again and wouldn't keep the freezer or refrig cold. 1st part only lasted 6-months. The simple fact is that the ADC used in the Maytag as well as others is under designed; I purchased 2-this time, 1's a spare, and you know it going to need to be replaced again. Sadly I'm stuck with this Refrigerator for at least 2-years before I buy another, it's only 5-years old. From my experience (with other Maytag products I've purchased recently) I'd never buy another Maytag product, ever! Since Whirlpool bought Maytag, I'm taking Whirlpool off my list too. Thanks Partselect for such a speedy delivery on the part everything back to normal, at least for now, wished I knew how long this ADC will last?
Constant running, ice build-up in evaporator, fridge side warm
Simple parts replacement. The temp control was a bit tricky as it involved replicating the bends of the tiny tubing for the sensor coil, but everything is so modular that it was not that difficult.
Freezer defrosted while doing the control repairs, it had a lot of ice stuck in the evaporator because the defrost function was not working.
The worst part of all this was moving the food and making sure it did not spoil.
I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!
Freezer was not staying cold enugh for ice maker to work. Discovered fan was not working to cool condensor. Fan motor would only run if manually turned.
Unplugged refrigerator. Removed lower back access panels and panel running up the back of refrigerator. Removed and disconnected old fan. Removed old fan motor from mounting bracket. Removed fan blade from old fan motor and placed on new fan motor. Connected new fan motor to power supply. Tested. Reinstalled.
removed card board protection.4 screws. Unpluged refrigerator unscrewed the screw holding the valve but not all the way. disconnected the electric connection. removed the water connection after disconnecting the main water valve. replaced valve by reconnecting everything. Turned on water to check for leaks. Easy fix and recieved the part sooner then expected. Will highly recomend your fast service and correct part replacement. web site was easy to use. THANK YOU
I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.
Extremely easy install. Just popped off the cover located on the side of the compressor. Noted placement of the wires on the overload and relay. Took a small screwdriver to slide both from the electrical pins on the compressor...take care doing this. Unplugged the wires, plugged the new components to the wires and installed to the compressor. Plugged in the frig and the compressor came on. Not sure why these went out to begin with but the fix was extremely easy and saved me the expense of a repair man.