JC15 - Instructions

(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

Repair went fine after I got the second element shipped to me. First element sent was DOA, so I called customer service and they credited my CC for part cost and shipping, then charged the new replacement to my account and mailed it out. Got it the next day. Repair was easy - turned off power to oven took out two screws holding element in place. Unbolted the two wires from element and installed new element. Oven element heated up cherry red and I am back to baking with an oven I thought was a gonner. Was impressed with customer service replacement process. It was fast and easy with no problems. Will buy again from PartSelect.com. Thanks

Use nut driver to take off shield. Pull out element to expose element and wire connections. Use nut driver to take off the 2 little screws. Remember what side is positive(red wire) and what side is negative(black wire). Put shield over the 2 wire and reconnect to element. Will need a standard screwdriver for the new screws. Slide wires into insulation and put back on shield.

Replaced lower element

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Attached the wires to the new heating element, screwed it back in. That's it.
I was glad they had the part for such an old oven.

The repair seemed very easy, even before I attempted it. When I recieved my part it was very obvoius that this was my problem part. The old element was worn out(21 yrs old). Having Thanksgiving around the corner, my wife was happy we had a fix to our not ready to replace oven. I was very pleased with your website picture matching choices and the very fast shipping you offered.
Thank You RR from Massachusetts

Removed the panel screws that hold the bake element to the back of the stove. Then I disconnected the old element from the wires. Attached the new element using the provided screws. Reattached the old panel screws to hold the new bake element in place. Works great.

The new bake element doesn't have an item number on it, so I kept the old element in a cabinet someplace in case I have to replace this one again some day. I've lost the model number for my very old GE wall oven, so without that item number I'll be in trouble.

It was so easy, we got on the General Electric web site and entered the old model number, found our match and ordered the part. It came 3 days later and it was so easy to remove the old one and install the new one, only two screws to remove. Saved a lot of money by doing it ourselves! Thank goodness for websites like this!!

Super easy, 1 2 3 steps and your done. Make sure to turn power off, remove two screws off of back plate. Remove two screws on wire connectors. Throw old element away and connect both wires to new element and screw back into place. Turn power back on and start cooking.

very easy--cut power supply 2 screws then 2 more on element quick and easy

The repair was a bit difficult because the screws connecting the wires to the element were small threaded bolts and no slot for a screw driver. They were very difficult to break loose - that's when we used the Liquid Wrench and waited. Other than that, the repair went smoothly. It is better to remove the oven door, if you can, otherwise the rear of the oven is not as accessible. It is also a good time to change the light bulb.

diagnosed repair by installing heating element from lower oven into upper oven, and it worked. Ordered proper replacement part and installed using tools above. No problem besides the tight space.

Following common sense, I removed the broken bake element by first removing two retaining screws and then disconnecting the element from the internal wires using a nut driver for both operations. The new element was installed in reverse order first using a screwdriver to attach the element to the internal wires (the new element had embedded threaded openings and came with two new machine screws) and then using the nut driver to secure the element to the oven wall.

Purchased the element from Partselect online -delivery was great -installed the new element in less than 10 minutes - the stove is now 100% again

Great Service

First I turned the circuit breaker off, then I removed the two screws with a nut driver, that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires with a straight scewdriver.

Reversed the the above process to install new element.

Oven was 27 years old.

Repaired and operational in less than 15 min.