Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
one of the burners was not working, the terminal block that the burner pluges into was burnt
I followed the instructions given to me in the package and all went well. I cut the old wires off the burnt terminal block, stripped the wires, installed the wire nuts with the shrink rap, installed the new terminal block and burner. The new burner is working great! Thanks
After staring at the online pictures of possible replacement bake elements, trying to count the number of squares to figure the length and width of available oven bake elements (some of the pics had listed measurement some did not), I settled on a push on element, since there were no matching screw in elements that appeared to come close to the measurements needed. Since it was a push on, I had to drill out the holes a bit more to fit the screws which took some time and finesse. It appears to works and it at least has enabled me to put off my bigger decision of buying a newer oven for a bit.
the drip bowls were a mess- rusty and beyond cleaning
I removed the old drip pans, cleaned the range top, washed and installed the new drip pans and put the old pans, box and packing materials in the trash. In only 12 minutes my range top looked like new and the mess was picked up. Now, if I could just get the rest of the kitchen looking that good that fast!
I simply replaced the element. HOWEVER, the most wonderful parts of this repair...Because of the pictures and closeups and descriptions I knew exactly 'what' to order! And I had the replacement in less than 24 hours. I can do some home repairs but this company provided such detailed information AND speed of delivery...that this was a no-fuss fix. I'll definitely stop by to buy, again. Thanks!
The original drip pans had rusted and needed replacement.
We tried to find the replacement pans at the local hardware store and were disappointed in that although they were cheaper, they were not deep enough to handle the heating elements. We were delighted to find that the parts from PartSelect.Com were genuine GE parts... installed in minutes and were delivered VERY quickly!
Oven wouldn't bake - visible damage to heating element
Unplugged oven. Pulled out from wall and removed backside access panel. Unplugged 2 stake-on connectors connected to element. From front side of oven, removed fan guard using 1/4 inch nutdriver. Gained access to and removed two screws holding in element. Pulled element out. For installation, reverse process.
Flipped off the breaker for the stove. There were two screws holding the old element in place. Removed those, pulled the element out a little to expose two wires, disconnected those, swapped in the new element, reconnected the wires, and screwed it back into place. Flipped the breaker back on and voila! Barely more difficult than changing a lightbulb.
the burner trays just needed replaced for an 85 year old senior citizen
Removed burner trays, pulled out heater unit, cleaned up inside of area around all four burners, slipped the burner trays back in and pushed the heater unit back into place.
I pulled off the back panel and the two wires were attached to the back of the know for the burner that did not work. I unhooked the wires, fed the new ones into the same slot and clipped the block in place. That was it!
Prior repair job had spliced the terminal block wires with electrical tape; electrical tape caught fire while making pasta.
anyways, disconnect all power, remove burners, pull stove out. you'll need a 1/4" drive socket to get the back cover off; six bolts total. phillips head screw driver to unscrew the terminal blocks; replace with new terminal blocks; it did not seem to matter which wire plugged into the back. put everything back together. very easy.
First, we ordered the part on Sunday afternoon online. It was here by Tuesday morning. We unplugged the oven and removed the screws holding the element in place and the electrical contacts. That was the toughest part because it's hard to get in the oven and they were baked on pretty well. We had to drill holes in the bake element. Be careful not to drill them too big, so the screw will fit snug and make contact. We screwed the bake element to the contacts, then back to the over, plugged it in and turned it on. The temperature is more constant and steady than ever, and the oven heats much faster. We were impressed and happy to avoid replacing the whole stove.
I removed the two screws that hold the element in place. I pulled the element out about three inches and disconnected the two wires. The screw holes in the new element would not accommodate the old screw size so I enlarged the holes to fit. Connected two wires and replaced two screws that hold element in place. End of story.
First I unpluged the appliance. Then I removed the cover from the back of the range. I then disconnected the two wires from the element. I then removed the two screws that hold the element in place. I then removed the old element and reversed the process to install the new one.
