JB36NXFXLW02 Jenn-Air Refrigerator - Instructions

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

My ice maker would not produce ice. I removed motor module which involved removing ice maker from freezer, removing motor module cover and 3 screws. I found short (burnt place) in copper of existing module. Ordered new motor module, replaced, and all is fine. Great service, quick delivery and correct part.

Used the instructions on your site.

The repair (really replacement) took less than 2 minutes. You press a button to pop out the old filter and stick the new one in. Easy as pie.

Had to Test Seloind. It Was OK. Then tested Motor Motor For Ice Maker. It Was Bad. Went Online Looked Up Parts For My Unit. They Were Shipped in a Timely Manner, only a few days. Installed parts in less than 15 minutes. Went very easy. Thank You

It was simple using PartSelect to locate the likely source of the problem. Also the pictures of the part helps confirm that you have the correct item.

Told Wife To Watch The Instructional Movie, Got Me A Beer And Watched Football. She Finished In about Thirty Minutes.Good Job

Completely on my own. Neither the owner's manual nor the instructions with the filter are of any use.A two or three panel series of diagrams with description of the process in English could make it simple. The release and reattachment of the filter are a bit difficult and need to be described as such.

After unplugging the microwave and removing the screw, I removed the old bulb and put in the new one!! I made sure it was in securely and the difference in the light was awesome! I use this light when I bake bread and let it rise inside the microwave, but DO NOT turn it on. The heat from this light helps the bread to rise properly!!

It was easy deterimining the fan needed replacing because it was very loud. I turned the refrgerator off, removed all the bins and shelves from the freezer. You also need to remove the metal sliders and posts that hold the bins and shelves to get the lower back panel out. the motor can be removed without any tools once its exposed. you first have to pull the fan blade off, just pull up, it slips off easily, disconnect the wires by pulling the connector apart, and to remove the motor, squeeze the bracket together while pushing up, it pops right out. I bought the motor kit which included a new mount and vibration isolator, plus a couple of other items that i didnt need, its a good thing i did because the old vibration isolator had deteriorated and was hard. I recommend that when installing the new motor, insert the vibration isolator into the motor mount in the refrigerator first and then push the new motor into the isolator, it goes in very easy that way. Then put the lower part of the isolator in the bracket and install the bracket. If you try to install the bracket and isolator on the motor first, you will have a difficult time installing it into the bracket in the refrigerator. Finally, install the new fan blade by pushing it onto the shaft, hook up the connector, and turn on the refrigerator. If it works fine, reinstall the cover, shelves and racks.

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

Took off Old Cap Put Knew One On.

push button take old one off put cap on new one,push it back in.easiest thing ever.