HYE2205AGW Maytag Dryer - Instructions

First, I unplugged the dryer. Then I used a flat screw driver to pop the top open. I removed 2 bolts from the front cover and removed the front door cover. I also took pictures of the electrical connector on the door so I would remember how the wires went back on. Then I removed 4 bolts from the front drum guide and lint screen holder. This allowed me to remove the drum & old belt. While the drum was out, I pried an access panel open on the side of the dryer. I then glued the new back felt piece in place. I put the new belt around the drum and re installed it. I re-installed the front guide and front cover re-connecting the door electrical switch. With the access panel open, I attached the belt to the motor. I then plugged it back in and turned it on to verify operation pryor to snapping the top cover back in place. Very easy repair.

Wife wanted a new dryer as it was useless without a knob and tired of using plyers to turn it. Went to internet, entered dryer knob, lead me to your site and item within two minutes. Ordered and received in 2 days. No tools necessary, just pushed it into place. Saved the cost of a new dryer.

removed the dryer female part that was broken with needle nose pliers and inserted the new one, on the door i removed one phillips screw and r/r the male piece with the new one and re-inserted the screw. that was all, very easy repair

Because the wheel had stopped and the shaft kept turning (junk from child's pocket got in there), the nut stripped itself away from the wheel causing low RPM and low air movement (lazy flame, vibration and clothes not drying)

I had to use a screwdriver to break the wheel away from the center nut and remove the fan. I then removed the air fan housing (3 bolt behind the fan wheel). I used a small pair of vise grips to hold the motor shaft staionary while I used a pair of channel lock pliers to remove the nut that was molded into the fan from the motor shaft. It was harder to get the nut started then I would have thought.

Once complete, I put the fan housing back on and threaded the new wheel on easily. The motor has external fins on it which turn with the shaft-I held one lightly while I threaded the fan on to keep the shaft from turning. Tighten just slightly more than hand tight-don't go crazy-it's threaded to stay tight with rotation. Works great and very quiet now.

Squeling from inside dryer. To Fix-
Pry dryer top cover off by popping cover off the two fastening clips located at about 3" inward from the two front corners. A screw driver at these two locations is easily inserted between the top cover and front panel.
Next remove the two screws on the top inside of the driver approximate size 5/16 inch. Pull the top of the front panel outward and then note how the lower portion clips into the fram, lift the front panel off the clips and roll it to the right. Remove the 4 screws and bulkhead.
Draw a picture of how the belt wraps around the drum and idler. Also note the belt orienation on the drum. Roll the belt off the idler pully and reomve the drum.
Replaced Idler asembly by first removing the tension spring and lastly the retaining bolt.
Reinstall everything in reverse order. Can be a bit tough getting the belt around the idler and motor pulley however this is managable. My machine runs great now!
Once again Parts Select comes through with great delivery, perfect fit, good pricing, accurate parts list. This is my third purchase and I have been 100% pleased. By far the best on line service I have ever experienced.

I just inserted the door catch, which by the way fit in perfectly. Thanks. Took 5 seconds to repair.

I opened the front panel and removed the heating element from the rear of the dryer by removing the two screws that held it in place, and slid the element out. using a mulitester I checked the High limit Fuse and it was not working.I ordered the part and replaced it. Everything worked great for two days and the dryer stopped heating again. My brother asked if I had replaced the thermostat because something burned out the fuse. He was right. I ordered both parts and replaced them. Every thing is working just fine. Save some money and time by replacing both parts at the same time.

Switch can be removed from outside of dryer and your video described the repair as having to work from inside dryer. But since wires were still attached to old switch, it could be popped out and wires switched. Since there were three wires on new switch to allow it to turn on and off a circuit, it was useful to check the resistance of the switch compressed or released to be certain I was attaching the two wires to the right two poles of the new switch. But that all required only a couple of minutes. Thank you.

Remove front pannel
remove wires to light and switch
remove drum panel
disconnect motor wiring
unscrew motor mount
replace idlerlever replace belt reassemble all parts

1. Disconnect power and hose. Use a putty knife to release top of dryer. Two restraints couple inches in from each side on front. Raise top and do not remove. Block it up in vertical so it doesn't fly down to back.
2. Disconnect five wires at front. Use magic marker to mark re-installation instructions on underside of top.
2. Remove metal screws (2) that hold front to frame. Remove front.
3. Pull dryer forward and put cardboard box, or some such thing under back to support when laying dryer down.
4. Remove frame (4 screws) that supports filter assy and front of drum.
5. Remove belt. Mark assy. sequence on underside of top.
6. Remove drum.
7. Stand dryer back to upright position.
8. Disconnect spring from idler lever. Drop light may help here. Note position of lever for re-install of new.
9. Unscrew bolt that holds idler lever. Nut is on back of bracket. Must re-install this way as bolt has pivot surface for lever on front side.
10. Install new lever and reconnect spring.
11. Lay dryer back on box.
12. Put drum back in place. Insure it seats well all around the felt gasket. Any misalignment here and it will not rotate smoothly.
13. Put belt around drum using small pieces of tape to hold it into position around drum, and them depress the idler lever and install belt around motor pulley. Rotate drum to insure it rotates smoothly. Remove tape.
14. Re-install filter bracket and insure drum seats nicely in felt gasket. Again, rotate to insure smooth operation.
15. Pull dryer back to standing position and reinstall the front, and re-connect the wires.
16. Lower top and push down to reconnect locking devices.
17. Plug in dryer and turn on to see if all is well.
18. Re-install hose and start drying all those clothes.

I watched your videos - they're great! The strike was installed in less than a minute and voila - the dryer was as good as new!

removed lower front panel, two screws on bottom edge. Limit thermostat located on lower portion of vertical panel at rear of dryer. I was able to detach the two wires and removed the two thermostate retention screws with a nut driver. Since I could only operate with one hand, I taped the new thermostat in place lining up the screw holes in order to replace the two hex screws. reattached the two wires and front panel.

I am not mechanical so if I can do it so can. UNPLUG THE DRYER FIRST!There are two bolts on the back of the dryer that connect the control panel and the dryer itself remove these and take out the brackets that are held by these two bolts, I used a socket, lift up and peek in to the front top you will see two screws that hold the other side of the top of the dryer lower the back side and move to the front of the dryer now that the back bolts are removed. Take a large screwdriver and place a dishrag or handkerchief so the flat side is inserted where these screws are located{preventing scratches}pry upward it will seperate the top of the dryer from the front of the dryer move over to the next screw and repeat now the top is loose and can be slid backwards until there is room for you to see down in front of the dryer, notice there are three wires that connect for the light on the right hand side, take the time to write down there color and in what order they are located as you will have to remove these now inside the front panel from the top about a third of the way are two bolts, one on the left and one on the right use the socket to remove these now pull the front panel to you and lift up, the front panel will now come off set aside. remove the three screws that attach the plastic vent from inside the dryer,pull out plastic vent, vacuum out dust and lint install new plastic vent install the three screws from inside the dryer drum and reverse the process you are finished!

Open bottom panel and observed back left drum roller wheel wobbling and obviously making the loud rumbling banging sound. Search goggle for Amana model part -- found partsellect.com, and read the list of other DIYs:

Take off the lower and upper front panels (two screws
each);

Remove the front drum glide holder (four screws. Careful
here because of the two wires to be removed for
door open off switch;

Pulling drum forward only enough so the bad roller wheel
would come off shaft after removing shaft snap ring
keeper;

Grease new roller hole and old shaft then place the
new wheel roller on shaft;

Replace all items back after cleaning lent off.

Note: Snap ring was a bit tricky (need snap ring pliers)--make sure it is clipped back all the way on the shaft after new wheel is installed. Also, I thought it was a good idea to put something underneath the dryer drum to support it while it was slightly pulled out -- a block of wood, etc. I found a spot remover plastic bottle that wedged up to support the dryer drum enough to take pressure off the belt during wheel replacement.

Ordered new lint filter, which did not quite fit. Called company and was told that filter had been redesigned to remove the felt surround, and that sometimes the new filters did not seat well. It turned out that the exhaust pipe was filled with packed-down lint causing the new filter not to go all the way into the slot. My husband surmised that that was why the first filter broke because volunteers at the Humane Society adoption center were trying to shove the filter into a groove that no longer worked. He took off the top, the front, and one other piece before removing all of the lint he could reach. Once that was done, the filter fit fine.