Models > HDA467K-02 > Instructions

HDA467K-02 Hotpoint Dishwasher - Instructions

All Instructions for the HDA467K-02
76 - 88 of 88
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher would not drain properly
On this model the panel under the door can be removed by unscrewing two hex screws on the upper panel and two phillips head screws on the lower vent panel. The drain solenoid is located on the left side of the pump and can be accessed easily without pulling the dishwasher out from under the counter. The solenoid is held in place with two phillips head screws, and the plastic actuator that is attached to the valve stem is simply press fitted on and held in place with a retaining ring. All necessary parts are included in the repair kit.
Parts Used:
Drain Solenoid Repair Kit
  • Muriel from Pascoag, RI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
End cap broke
Ordered the part from you and it was easy to replace.
Parts Used:
RACK SLIDE END CAP
  • James from Las Cruces, NM
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
See below
In replacing the upper rack in our dishwasher, I struggled and broke one of the end caps (see previous tale of woe. With the new end caps, I finished the job in less than two minutes with no tools. BUY END CAPS when you order a rack!
Parts Used:
RACK SLIDE END CAP
  • Leslie from Amarillo, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Dishwasher leaked badly when running
At first, I found a metal band that was rusted and loose, replaced it but still had a leak. I went to the diagnosis section and identified another area of problem, ordered the part and got super quick delivery. With the help my wife I was able to pull apart, repair and get the unit to run and stay dry. Wife is happy because she loves the décor of our old but now dry dishwasher.
Parts Used:
Impeller and Seal Kit
  • Kenneth from Lake Bluff, IL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Torn rubber seal in hub assembly
Remove lower rack from dishwasher to provide easy access to spray arm/hub assembly. Removed hub/spray arm assembly from base of dishwasher by unscrewing it from the base of the dishwasher. You should be able to do this by hand. Then unscrew the upper spray arm from the hub. This is the telescoping tube that pops up from the center, and it is reverse threaded, so loosen it like you're tightening it.Remove the Phillips head screw holding the spray arm to the old hub. Transfer the upper spray arm assembly to the new hub. Screw the whole assembly back on the threaded connection it came off of. Hand tighten only.
Parts Used:
Spray Arm Hub Support
  • Michael from Annapolis, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Upper Rack difficult to open
The initial problem was that the top rack was difficult to slide out. I purchased a new set of upper rollers. In order to remove the roller you must slide it off the rail. To do this, you must first remove the end cap. I broke the end original end cap trying to do this. The new roller installation was simple. So was the installation of the new end cap. Simply press it on.
Parts Used:
RACK SLIDE END CAP
  • Dan from Oak Ridge, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Water leak from gate (diverter) valve
Read Joseph from Livermore, CA for good instructions. I took a camera phone photo for reference before I started. Should have taken another photo half way thru. Probably put the push-on-nut on backwards as it didn't 'lock' in - had too much play in the shaft, would have leaked. Impossible to get nut back off in good shape. I put original mangled push-on-nut on also - it added enough tension to eliminate play in the shaft. No leak..but lucky. Go ahead, you can do this repair for under $20.
Parts Used:
Push On Nut
  • Robert from Oak Island, NC
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
multiple rust spots on the old rack
Original part no longer made. Substitute too small by a half an inch. Corrected the problem by removing the 4 corner wheels from the old rack and put them on the new one. Now, it fits and works perfectly.
Parts Used:
Silverware Basket (Grey)
  • Clifford from Saint Louis,, MO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Washer didn't clean properly in either the upper or lower racks.
I didn't see any obvious defects in the washer like a plugged drain or obstruction in the pump intake, so I decided to try a new lower spray tower. I loosened the tower with a large pair of channelocks (arc joint pliers) by grabbing it near the base. The unit unscrews in the normal manner, i.e. counterclockwise. Once it's loose, it can be removed by hand. Thread in the new tower and snug it down. Done. Cleaning problem solved.
Parts Used:
Lower Spray Tower Kit
  • Robert from Addison, VT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Pump was leaking from the shaft seal
Removed and inverted the DW. Removed the impeller, grinder, screen and seals then the actual shaft seal. Replaced with new parts in reverse order. Instructions provided with the seal kit were simple and excellent. They were right to the point.
Parts Used:
Impeller and Seal Kit
  • Anthony from Mechanicville, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Old Basket Broke
Ordered a new basket it was a little large as I ordered the wrong size. I just broke of the tabs that held it in and now its perfect and larger !!!! Simple and great service !!!
Parts Used:
Silverware Basket (Grey)
  • FRANCIS from WINOOSKI, VT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Lower rack had rusted through in several areas.
Pulled out the old and rolled in the replacement. The easiest part of the repair was ordering from the PartSelect website and receiving it via FedEx Ground the next day. Thank you PartSelect. Even my husband could have been successful with this.
Parts Used:
Silverware Basket (Grey)
  • Bill from Fort Myers, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
dishwasher would not turn on the water
took off old part, put on new part and that was not the problem.
Parts Used:
Water Inlet Valve
  • Syl from Pagosa Springs, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the HDA467K-02
76 - 88 of 88
Back to Top