HDA3400G02BB Hotpoint Dishwasher - Instructions

The newly purchased wheels have a little different design and could be installed in a matter of few seconds.

pretty easy, take off 7 screws from inside door

only hard part was getting arm to click into lever through the door. if you practice with the parts outside the door they lock together really well :)

Very simple. By hand, I unscrewed the old spray arm and screwed in the new one. One brief hangup. The old spray arm was very hard to unscrew. Rather than seeming to force it, I called the PartsSelect 800 number and got advice. The tech reassured me that all I had to to was unscrew it and put in new one. So I applied more force and old one came out. A breeze.

Replaced lower rack with new. Upper rack removed front stoppers, removed old rack, slit new rack in and replaced stoppers. Total time about 15 mins.

Use screw driver for leveage, righty tighty, lefty loosie, easy as that, and thanks to Parts Select, ordered my part on Thursday by dinner time Friday had part, install no washing dishies by hand, Thanks guys

Brian Souza
Vacaville, CA

Removed dishwasher, took off motor, and ordered part. It was delivered in a timely fashion (3 days). Determined which directions to follow. Used screwdriver to hook up motor. Put dishwasher back into cabinet area, made sure there were no leaks before fastening the dishwasher in place. Took about 1/2 hour to complete process. Very satisfied.

Read directions. They were poorly drawn. Set them aside. Opened up unit on December 26th. I made careful observation of the wiring, two hoses, one metal bracket, the hose two clamps, and then proceeded. Instructions said 1 to 2 hours, to complete. Ha Ha, perhaps if you've done it before. It was actually really closer to four hours. When done, it worked perfectly. The best part, my wife said: "This was the best Christmas present ever!" That made my day! Dishes are clean again, just like new! Thank you: www.PartsSelect.com.

Went to repair parts on troubleshooting and found check valve assembly to be most common problem. Went to parts diagram to locate assembly and found it somewhat confusing as to exact location. Ordered part(s) on percentage as the problem. Received part next day (great)! Pulled dishwasher out and found I did NOT need to do so to replace check valve which is replaced without having to remove dishwasher. The gasket replacement was not necessary as it seals sump area from bottom of dishwasher and not the valve as it appears on the parts diagram. It took about 2 minutes to replace valve itself and it was the cause of the problem.

Ordered the part online and replaced the hoses. Very easy...took maybe 20 minutes

Flipped washer on side
Did repair from bottom
Really easy repair

Our older GE dishwasher was leaking water on the floor while running. After inspecting it while running I was able to determine that the water was coming from the seal around the motors shaft where it entered the pump. I then looked up the washers model number and ordered the impeller shaft seal kit. To my suprise the kit arrived the very next day! After disconnecting the power and water supplies from the dishwasher , I then removed it from the cabinet base and turned it over to gain easy access to the bottom. Using nothing more than a nut driver, adjustable wrench and a pair of pliers I was able to loosen the two compression clamps and two hose clamps that hold the pump to the bottom of the washers tub. I then removed the entire pump and took it to my work bench for the rest of the repair. Removing the plastic impeller strainer was the toughest part.. Lacking the proper spanner wrench, I had no tool that would lock onto the raised tabs to turn it loose with. I was able to position the tabs in the jaws of my workbench vise and giving the entire pump a little twist, It broke free and I was then able to unscrew the rest of the way it by hand.. The old dried up detergent made for a good adhesive, and after removal I cleaned the area completely so the new strainer would thread in easy. I installed the new parts in the kit as per the supplied instructions and re-installed the pump housing back on the dishwasher and put it all back in place. After running it several times not a drip was to be seen, and I was very pleased with the whole process. With the shipping it cost me just $25.00, and it saved me a expensive service call or maybe even the cost of buying a new machine. I would say that overall it was a easy repair but lacking the right tools, you may have some trouble removing the pumps plastic strainer screen as I did. I would highly recommend PartsSelect to anyone, and the entire experience was a good one for me.

I first made a bad assumption that the leaking dishwasher was from the gasket. I replaced the gasket and it still leaked. To find the leak, I took the body off of the dishwasher and ran it to find the leak. It was from the solonoid connection. I took photos of the leaking motor unit and very easily replaced the new motor unit by matching the placement from the photos. The hardest part is tipping the dishwasher on its side and mopping up the water.
It was very easy. All you need is a nut driver and a Phillips screwdriver. Even an over-domesticated, non- tool user can do it.

Ordered the new motor/pump here at parts select and with the easy directions I replaced in no time flat. Saved me $300.00 for a replacement.

Took old rack out put new rack

Unscrewed old one and installed the new one.