Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven will not warm up, or takes a very long time to reach temperature
Replacing an oven igniter is one of the easiest repairs you can make to your oven. There are two igniters - one for the broiler and one for the oven itself. Oven Igniter: Start by removing the rear panel of the oven which attaches with a couple screws. Inside the oven, remove the "butterfly" shaped heat deflector (over the flame tube) which attaches with four screws. You now have access to the igniter. Remove the two screws which attach it to the bracket. On the rear of the oven, unplug the two spade connectors. Pull the igniter out from the front of the oven. Fish the wires for the new igniter through the same hole. Plug the 2 new wires back in. You can't mess this up - the wires have matching connectors and you can't get them confused. The broiler igniter is a little more complicated. You will have to remove the side panel of the oven to reach one of the connectors. It's just a couple more screws. The procedure is the same, but the wires are much harder to "fish" through the hole though. Unscrew the broiler igniter from the bracket and unplug the wires. Before you pull them out, attach a length of clothes hanger so that you pull the hanger into the oven from the rear. This way you can attach the new wires to the hanger and then pull them through to the back of the oven. If you don't attach something when you pull the old wires out, it is very hard to fish the wires for the broiler igniter to the rear of the oven. Good Luck!
First of all I couldn't believe parts arrived next day. Parts solved the problem I was reluctant to believe new hinges would solve the problem. I installed the hinges in about 1 hour but I had door apart previously so I knew what I was doing. Now my wife is speaking to me again and she threw the wooden spoon away that she used to hold door closed. Just spent $100 dollars and saved $1600 thanks guys.
My inner glass on the oven door got cracked from spilling something cold on it, while it was hot.
Removed the door. Took out all the screws. Removed the glass that was cracked. Put in the new piece. Put the screws back in place. Put the door back on and it was a done deal.
Most of the basics have been covered in previous post. I can add this- those who claim 15 minute-fixes are delusional, unless they're appliance repairmen. Secondly- what will take time is the cleaning. If you have to do this repair, which requires extensive disassembly of the door, it would be foolish not to take advantage of the opportunity to thoroughly clean all four layers of glass. Take the glass panes outside and use oven cleaner. This takes time. Other than that, the pancakeing of the components on re-assembly is tricky, but you can do it. Don
Take 4 screws off to remove oven pan, once pan is off , you can see the igniter. Take off two screws and remove old igniter. Be sure to run wires on new igniter where they were on the old igniter.
Inner glass shattered due to dropping something on it
Following the various instructions here made this replacement much easier! I was able to do this on my own with just a screwdriver. Pulling the hinges out was fiddly but after removing the screw and small hinge plate from each side a little wobbling and pulling with the door open an inch did the trick. After removing the door I started with the inside glass facing up on a table, and mid-replacement needed to flip the door over. So, recommend that you start with outside of door facing up. As you remove screws keep in mind where they came from so you can replace in reverse order properly. Other than that, everything went swimmingly! Thanks to everyone for their great advice.
Remove the bottom panel and confirmed that the igniter was not lighting. Unsrcrew the igniter from the housing in the oven, then removed the back of the range and unplugged two leads from their conections and ran the wires through the insulated back wall of the oven. To replace the part just did the opposite of above. Piece of Cake. Want to say also that I was astounded at the speed in which I received my part. Ordered it at 3:30 PM on Friday afternoon and received it by 10 AM Saturday. And with standard delivery! Thanks!
I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.
This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.
