All Installation Instructions for General Electric Refrigerator GSL25IFRFBS

small leak in ice maker water tubing on the back side of the fridge

watched a 2 minute video on installing the connector. Then using the utlity blade cut out a 1/3" section of the tubing and installed the connector. DONE! Leak fixed

Parts Used:

Union Connector - 5/16 Inch to 5/16 Inch

Robert from Carlsbad, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Broken dairy door

Snapped the new door into place.

Parts Used:

DOOR DAIRY

Barbara from Lake Almanor, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

freezer and refrigerator wasn't cold

Replaced all the sensors in both the feezer and refrigerator.Even though it colder now it still is not cold enough.Freezer won't freeze items but is cold and refrigerator still not real cold

Parts Used:

Temperature Sensor

Laura from Brentwood, MD
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Wrench set

Was this instruction helpful to you?

Thank you for voting!

Refrigerator and freezer stopped working, only inside lights on

Really easy to change the board..I did spend more time trying to figure it out how to plug the ground wire, as the new board had different wires to ground. What i did was i switch the ground wires from the old board and put them in the new board. Problem solved, refrigerator and freezer running like new.

Parts Used:

Main Electronic Control Board

Marinez from Bridgeport, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Tempeature in fresh food section was unstable and dropped below 32F frequently. Service technician had previously replaced the two temperature sensors but this did not remedy the problem. I decided to replace the main control board and this seems to have have resolved the problem.

Removed the cover plate to gain access to the main control board. Disconnect the electrical connectiosn ad repalce the board. re-connect the electrical connections.

Parts Used:

Main Electronic Control Board

James from Crestwood, KY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Thank you for voting!

would not run no lights on panel control

real easy unplugged fridge took back small plate off marked and unplugged wiring plugs squeeze the four tabs still was tight coming off be careful or might break a tab i didnt but tight as it was knew it might happen so was very careful installed other board and put plate back plugged up worked prefect saved alot on repair bill for sure

Parts Used:

Main Electronic Control Board

Ricky from Panther, WV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Leak

Had a water leak on that valve for probably the last 7 or 8 years. Only noticed it when I had a huge water issue with a leaky faucet. Repaired that, went to repair the Sheetrock behind refrigerator and saw water in the tray under frige. Wiggle hose and realized that the reason the water on the front door would only trickle out was because the leak on that valve was also affecting the pressure on the front door. Unreal!! The website and video made it incredibly simple to replace, u guys rock, for real!!!

Parts Used:

WATER VALVE WITH GUARD

Frank from Lutz, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Socket set, Wrench (Adjustable)

Was this instruction helpful to you?

Thank you for voting!

Freeze and refrigerator sides at times were warmer than normal. Would not dispense water or ice threw door dispenser, also could hear a clicking noise every so often the last about 10 minutes at a time. I think the clicking would start on the main board when it went into the defrost mode. Defrost mo

UNPLUGGED the Refrigerator.Removed two screw from the panel on the (outside) back, took panel off, removed the wire harnesses, carefully removed old board off of the plastic pins, pushed new board on the pins, put wire harnessed back on in their proper places, put cover back on. Everything that was not working, was working now. Took less than 15 mins..

Parts Used:

Main Electronic Control Board

Winston from Ford, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Thank you for voting!

Air leaking into freezer through door dispenser

I followed the video instructions. They were clear and consise. I removed the trim ring and controls. Them removed the housing and flapper. I did notice a small burr in the plastic chute and foam insulation. I trimmed this off with a utility in hopes this burr caused the flapper to warp. This is the 2nd time the flapper has been replaced in 1.5 yrs. The repair was really easy thanks to the video.

Parts Used:

Dispenser Door Assembly or Flapper

Ray from Fredericksburg, VA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

No mention that plastic nut was left hand thread

Tried to remove plastic nut used as a bearing as a right hand thread. I put part in hot water and was still unable to remove nut and finally checked the new part and found out that part was left hand thread. It would be very helpful to have some brief installion instructions

Parts Used:

BUCKET AUGER

John from Meadowlakes, TX
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

broken dwr. slide

removed 2 screws from broken slide, then I positioned the new slide in place and using original screws secured slide to wall of frig.

Parts Used:

Drawer Slide Rail - Left Side

gene from Picayune, MS
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

ice dispenser shute was leaking and rusted

replaced parts that were ordered; all matched up and refrigerator is now operating at peak performance again. Much cheaper than having a repairman and now we know it is repaired properly. thanks for your help is having the parts we needed.

Parts Used: