GSD6660G00SS General Electric Dishwasher - Instructions

took off eight philips screws on inside door panel which then exposed the broken actuator and missing spring. Replaced broken and lost parts and reset actuator in door then reinstalled inside door panel. Done and I'm happy not to have called service.
Joe

I connected one end of hose to the drain using a hose clamp and screwdriver then connected the other end to the dishwasher using anouther hose clamp and a screwdriver..

After removing the screws, the front of the dishwasher easily came off. I put 2 screws back in to hold the control panel in place. I did not want that to dangle while replacing the part. The part came off easily after removing the screws. Everything went together easy.

The repair was easy. Removed all the screws from the inside door panel, approx. 11. Watch out for that last screw as there isn't anything else holding the outside panel, inside panel and control panel together other than those screws. I then unplugged the old dispenser backed out another 6 screws and replaced the old dispenser with the new one. Put it all back together within about a half hour.

The best money I've spent on a repair. Easy. The lower rack now rolls in and out smoothly.

Removed the old wheels and studs. Pressed on the new studs and wheels. Viola.

Called repairman: announced that the drain pump was gone. Did not seem right. Went to the website. Found what I was looking for. 49% of the time it was a check-valve issue; only 26% of the time was the pump the problem. Took the unit from under the counter; got it on its side; removed the drain pump. Found my first check-valve, but thediagram showed a second lower one toward the sump. Having located both and purchased two valves and and the lower holder piece, I was ready to finish the job. Quarter-inch nut driver and a screw driver and the valves were in and the drain pump re-installed. Most difficult in my case was getting the dw back into its spot and lashed down! Thanks for the good guidance!

I removed the old seal, cleaned behind it, and then put the new seal in. We saw a video on You Tube on how to do it. Partselect also sent instructions on a e mail with the order receipt. We enjoyed working with you guys. Your customer service representative was very nice and accurate in sending out the part. All went as she said it would. Thanks!!

Just snapped studs and wheels together and put them into place.

Popped the axle on to the wheel, then snapped it on to the lower drawer - done!

I am NOT handy, but my husband was gone when the wheels and stud/axles came. I was able to replace all of them in about ten minutes with no tools. Easy and no more frustrations!!!!!

Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.

Thought it might be check flapper valve on drain pump, so I replaced fairly easily, per instructions. When doing, I noticed the attached relay wires were not secure. When it was on the drain cycle one of the relay wires vibrated badly and loosened the connection enough to only work occasionaly. Would like to put new relay on the pump but they do not sell separately from the pump. (one assembly). I resecured connection and will wait till relay gives out and buy new assembly, but for now it's working perfectly!

Watched the video, and followed the directions. Although my machine had some slight differences, the repair went pretty much per the video. Got all connections back where they belonged, cleaned up the insides a little while had the door parts separated, then buttoned it all back up, ran a cleaning solution thru empty washer, let it dry then started filling with dishes and ran the wash cycle the next day when full. All is well.

flapper then bought the spring