GS6SHEXNS00 Whirlpool Refrigerator - Instructions

Exactly as shown in the video; had a bit of trouble with the wiring harness, but all else went smoothly. If it were not for the explicit video installation instruction, it could not have been done by a do-it-yourself guy with tools. I had ice again in 3 hours! PartSelect is the absolute best when it comes to diagnosing, ordering and installing the part(s).

Opened freezer section of refergerator and taped Ice Maker cover door in the open position to remove emitter and receiver boards. Unscrewed the phillips head screws that secure the emitter board housing to the refrigerator side wall. Turned off power to the refrigerator and unpluged the emitter, removed the 2 screws that hold the emitter board against the housing and removed it, then I installed the new emitter board in the housing by screwing it in place. Repeated same process for removal and replacement of the receiver board. The whole process took me about 10 minuets.

It was so simple, one screw to take the ice maker out and four screws for the motor. I ordered the motor because in your web site it suggested that 46% of the times its the motor the problem, I guess you could now say 47%. Got the part within 3 days. It was a pleasure doing business with your company. I recommended highly to everyone. Your web site was a lot of help.

I discovered the coupler was broken, so I went online to search for a repair. I found the part number for the coupler and washer. I used the short online video that shows step by step how to fix it. It was very easy and now the ice maker dispenses ice again! I researched Sears and your site, and your site with shipping was less expense than Sears. I called Sears and they didn't have the part in stock anywhere close to where I live to pick up, so with their price and shipping, your site was just a couple dollars cheaper. I receive the part very quickly after ordering.

Toughtoget the ta b into the paddle but once in it was ok.

Just replaced the old Push-On Start Relay and it started to work again.

my Husband took the part off.unscrewed some screws took the front off put the new part on the front put it in and awhile later ice.It takes awhile for ice to start.so don't worry.Don't call a repair man do it your self and save the service call money.I ordered this part in the morning got it the next morning.Don't know if they have a place near Jax.FL.or not anyway i was very impressed.And very satisfied and saved a little bit of money.Iwill use them again.And will tell my friends Keep up the good work.MaryLux.Jacksonville,Florida.

1. Turn off ice maker and Remove Ice Bin. 2. Remove auger drive shaft. Close door. 3. Remove dispensing console, two screws at bottom rear (slide out tray to expose). 4. Carefully lift and pull out console slightly to expose wire connections. Unplug wire harness from console. 5. Remove motor assembly (4 screws). 6.Replace motor. 7. Reinstall in reverse order, being careful of gasket alignment between motor and drive shaft port. May need extra hand aligning and reinstalling drive shaft, gasket and motor. 8. Plug in wire harness. Be very careful not to damage circuit board! 9.Replace console, Turn on ice maker, Clean up the mess so wife is happy and enjoy one on ice!

I removed the door and switched out the cams on the bottom. Super easy. Door closes perfectly now.

i talked to a gentlman name Ruben and directed me to the parts i needed i ordered them and put them by myself i ended up saving over 200.00 dollars thanks to Select parts the minute i finished the process and closed the freezer doors i could hear the ice is comin down again it was good feeling. After i changed the emitter and the receiver this year every thing is working again

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

He removed the front of the motor box. He then took the motor panel off and replaced it with the new one! So easy!! We have been buying ice or getting it from a friend that has a commercial ice maker. I could not believe it was that simple and the delivery was unbelievable. I ordered the part either Thursday or Friday and FedEx delivered it Saturday! Thank you so much. Now I have all the ice I need!!!

No instructions with part. Found a picture on line and changed the arm, but it didn't fix the problem. Fairly easy after figured out what needed to be done to get to the part.

Watched a couple videos on youTube that walked us through the process. We aren't very "handy" people, but decided to give it a try. The videos just walked us through step by step. Easy! And this company provided FAST delivery!!

1) Removed 1 bolt that held a cover for the wiring harness. 2) slid out assembly 3) unplugged wiring harness. 3) removed the base from the old and attached it to the new [3 bolts] 4) reversed steps 3 thru 1.