GS2327GEHW Maytag Refrigerator - Instructions

Purchased two new shelves and installed them into the freezer door,. they just clipped in.

First I compared the old parts and new parts to see if I had ordered the right thing then I inserted the new stop into the door. Since the stop has a lip that needs to fit into the slot I the door, I used a hammer to push the part up so it would lock into the hole. Very Simple

The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

Very easy to order from parts select. Took seconds to replace.

No tool required! Pulled out tray, emptied ice into large bowl for reuse. Pushed in and pulled from inside the coil springed auger until could get old plastic ring off and put new one on. Useing care not to apply too much pressure to ice dispensing end so as not to break housing. Have to turn auger assembly at an angle to compress enough and get old ring off. Needs a little physical strenth & care not to force plastic housing to breaking point. Worked great reused saved ice. Took less than 10 minutes

Replaced filter with by-pass plug. For some reason though, ice maker does no longer functions, although there is flow out of the cold water tap. Is the design of the bypass plug such that, when installed, it impedes flow to the ice-maker?

Thanks

Replace the refrigerator lightbulb while traveling 88 mph then turned on the flux capacitor being carful not to get stuck in a worm hole. This allows you to fix the problem before it starts to go bad.

Took a putty knife and
Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place

I watched your online video on how to take out the old filter, and then to replace it with the new filter. It was as easy as on the video. Thanks!

Viewed the repair video. Removed covering. Replaced limit switch, control board, and solenoid. Very easy repair!

Once I identified the bit that would remove the screw, the rest of the repair took 5 minutes. I removed the screw and discarded the remains of the original but now broken shelf support. With the same screw I simply attached the new shelf support that I received from PartSelect.com. End of story.

1. Unplug refrigerator and remove fountain drip tray.
2. Remove the two #15 torx head screws that were covered by the drip tray.
3. Pull the bottom of the trim panel out and push up to remove panel and then unplug switch circuit board connector..
4.Remove the three screws (same size as the other two) and then remove the switch, ice door, etc assembly and unplug the connector.
5. Aside. At this time I extended the water hose which has been short since new. Used a couple of inches of 1/4 inch plastic tube. Heated it with boiling water and slipped it over the existing tube to extend it about 1/2 inch. Now the water flows in a uniform predictable stream.
6.Remove the tiny phillips screw holding the switch in place.
7.Remove and replace the old switch and actuator pad and screw. Check operation of switch. I lubricated the surface between the switch actuator bar and the rubber with a little plastilube(white) grease. Probably highly optional.
8.Replace and replug the assembley. Tuck the actuator pad around the edges if needed. Remember to turn the screws CCW until they fall into the old threads and then tighten them until snug.
9.Plug in and mount trim and connect refrigerator.

Took the glass out of the package, attached the shelf trip and popped that sucker in!!
Easy....easy....easy!
THANKS!