Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Our ice and water dispenser was "running on" and spewing onto the floor each time it was used.
We removed the old part, which actually looked quite functional. We put on the new part, thinking that the repair was not going to be effective, and that we were going to need other parts. But, the refrigerator is working perfectly now, and I have no more run-ons onto the floor. THank you very much.
Plastic parts wear out like clock work every six months.
I removed the top refrigerator side hinge screws. The door came right off. Slipped in the lower hinge pin.. Unscrewed the natural door closer and replaced. Reinstalled the door. It is unfortunate that these parts are plastic. They wear out way too soon. No, the door is not over weighted. If you have no weight in the door the plastic shelves will hinder the door closing. Putting stuff on the shelves makes them take their proper form.
At first I thought I had ordered the wrong bracket but all I had to do was push it up and pull down and it snapped right in place. If a 71 year old lady can do this any body can do it. Thank you for the fast service.
Door would not close all the way - cold air leaked and condensation & ice formed in fridge.
After taking advice from the other posts, I removed all contents from the door, removed the screws from the top hinge and then lifted the door off the bottom hinge pin.
While door was lying flat I unscrewed the old natural closer, replaced it with the new one. Swapped out the old lower hinge pin with the new one.
I then had someone help me lift the door back on the hinge pin and fastened the top hinge screws while they held the door in place.
Lower hinge broke, causing the door to jump when open
It is the model with the french door. I unplugged it, removed two screws at the bottom of the door, while holding the door from sliding down. Removed the door and put it on its side. Removed one screw that was holding the hinge, removed the hinge and replaced it with the new one. Put the door back on (do not forget to reinstall the shims). Did the same thing on the other door. After putting the door back on readjusted the height to level the door, using height adjustment screw. Lock the door in place. It now works better then new
Ice dispenser auger broke loose from Ice Enclosure
I followed the directions from John from Virginia Beach, with the added warning: Unplug the electrical connection and bring the whole ice enclosure out before you remove screws holding the relay and motor to it so you can see how it goes together. When you remove the relay, notice that a metal cylinder (Michael from Vienna Va calls it a magnet) slides out of it. If possible, keep this unit together. If it comes apart, notice there is a spring on this metal rod. Don't lose the spring and remember how it all goes back together. This job was just as easy as it should have been.
The biggest problem I had was finding how to remove the old broken support. I did a google search and found the answer on your web page, grab it with pliers and rotate it 90 degrease then pull straight out. Installing the new one was even easier just do the reverse.
Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.
The door switch was broken so the interior light would not come on.
The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!
I pulled the drive ring off of the icemaker and replaced it with the new part. Saved a $150 service call plus cost of part. It cost me a little over $11.00 and a repairman probably would have charged $30.
Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.