GS2121NEDW Maytag Refrigerator - Instructions

removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.

1. mark location of removable baskets in door and remove baskets
2. remove three screws in top hinge - save shim under hinge
3. lift door from lower hinge
4. remove 3 screws from lower hinge bracket and remove bracket
5. install lower hinge bracket with 3 mounting screws
6. install lower hinge pin in bracket
7. clean upper and lower hinge holes in door
8. lubricate upper and lower hinge pins with grease
9. place door over lower hinge pin - the magnetic seals will hold it in place
10. install upper hinge bracket with 3 screws
11. install baskets in door

Note: The plastic piece on the bottom of the door that mates with the hinge pin and provides a cam action should have been replaced at the same time.

Most of the time was sent to removing and replacing door shelves. Pry off upper hinge cover. Easy, it's only plastic. Remove 3 fastener from top hinge and remove hinge. Lift door off lower hinge. Lay door down on table let handle hang over edge. Remove door closer attach fastener. Remove and replace door closer. Pry lower hinge up and out. Tap new lower hing pin into place. Replace door, upper hinge and hinge cover. Had to replace Door Closer and Hing Pin together; both were worn and needed replacing.

Pry old switch and pull out. Disconect two wires. Put two wires on new switch, must be inserted right and connections not loose. Put switch in, making shure wies do not come off and snap in place

Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.

Part was easy to order, delivered quickly, installation very easy. Just unplug the unit, pop out the old swich using a screwdriver, disconnect and reconnect leads and pop switch back in. Definitely recommend that you can do it too.

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

This was easy. Removed the plastic cover at the top hinge. Removed the 3 screws at the top hinge. Lifted the door off of the bottom hinge and laid it on it's side. The part that was worn out is the "natural door closer". It looks like this part will need to be replaced every few years, it is made of plastic and was ground down to nubs. Remove the screws holding it down and replace it with the new one. Lubed it up with some WD40 to get rid of squeaks. I also replaced the lower hinge pin, but I don't think that was necessary.

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

Called a serviceman. The Air return cover is NOT the cover we replaced. Ours is 3/4 of the way down on the freezer side of fridge. Put a thermometer inside, to monitor it.