GLEFZ384GCA Frigidaire Range - Instructions

With no install instructions (NOT good for diy-ers), looked through reviews and watched video for help. Replacement part - not same as original. Had to use magnifying glass to id the terminals / take a picture before disassembly. reassembled - found out terminals are different & black wire is too short. Took off element - rotated the clips one number counter clockwise, reassembled - removed black wire from harness for extra reach. Hooked up, lowered top for test. power on - everything OK. Power off - complete assembly. Power on - test. Seems to be good. When I called customer service for assistance because there was no instruction, they told me I should contact a local appliance repair person. (big joke).

Replaced switch by according to video with no issues, Terminals were nearly identical as the new switch.

The terminals on the new burner were not located in the same position as the terminals on the old burner. I had to reference the wiring diagram to locate the correct wire to terminal location. There was not enough slack in the wires to position the new burner in the same position as the old burner. I had to rotate the new burner so the wires would reach. This cause me to have to rotate the warming burner because rotating the new burner, the terminals interfered with the terminals on the warming burner. I also had to reposition some of the wires so they would not contact the burner and terminals.

Replaced the dual element switch and that fixed it up

repair was exceptionally easy. Did not need the fiberglass tape that was mentioned in online repair steps. Just slipped the wires off and then back on the new element. Any 70 year old can do.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

Quite easy: Removed the two hex head screws with a 1/4 inch nut driver. Gently pulled the old element out of the rear of the range with the connectors still attached. Next I disconnected the connectors from the element and attached a small "paper binder" clip to each of the connector wires to keep the connectors from pulling back through the "Hole". Lastly, I connected the two connectors to the new element (released the clips) and gently pushed the unit back into place and re-secured the hex screws. ALL DONE! Very very easy....

I looked up the problem on YouTube and it said it was the oven temperature probe was going out. So I ordered the probe and it was shipped out, received within two days. Took out a few screws on the back of the stove installed it, put it all back together and it’s working perfect.

Very simple repair.. repair guy said if it was the control board to buy a new oven. Searched for the part found it here for under 200$ shipped.

The actual repair consists of 6 screws outside, 4 holding the control board in place, and few wires in a harness. To make swapping easier, took a picture of where wires connected, they are color coded.

removed the old burner and put the new one in it's place.

turned power off at fuse box took of back panel about8-10 nuts unhooked wires with pliers that went to element then took2 nuts out that held element up and 2nuts holding element took out and put new one in works great

I am a DIY kind of wife. My husband works late most nights and I get home in the afternoon. It was really quit simple except for the element plug slipped into the back of the stove. So I had to pull the stove out from the wall and take a couple of screws out of the back and push the plug back through. It was scarry for a minute but it all ended up just fine and we had a wonderful dinner that night.

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.

Remove screws from back of oven after unplugging oven. disconnect wires from element by sliding of element. Remove screws holding element inside oven and slide element out. Replace element by doing everything in reverse. 20 minutes tops.

Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.

The youtube video clearly described how to remove the back panel and how to replace the probe.
The repair took maybe 20 minutes to complete and 1/2 of that time was spent cleaning behind and underneath the range!
Range is working perfectly now!