GHDT108V60BB General Electric Dishwasher - Instructions

Simple repair... Great Company, quick shipping (in CA had it the next day). Quality parts, GE OEM!! And to top it off the lowest prices!!

All I had to do is take out the rack, pop off the old wheels, place the new stud rollers on, then pop on the new wheels. So easy and now my dishes don't get chipped when I pull the rack out and push it back in. I wish I didn't wait so long to order new parts.

Pull old rack out, slip new one in!
One thing i did was order wheels and studs as i was unaware they lower rack came fully equiped with all wheels,studs, and flip up dish dividers. So if your replacing the rack no need to order the wheels! The diagram made it look as if you only et the wire rack and not all the added pieces.

I removed the old wheels & studs on the right side of the bottom rack of the dishwasher, and I gleefully THREW THEM ALL OUT! HA HA!

Then I put the nice new rollers on the studs, and then I put them on the rack.

Helpful hints for others beleaguered by this design problem:

1) Be sure to get new studs - that's the part that kept causing the wheels to fall off

2) Put the rollers on the studs before putting them on the rack. (Another user on this site noted that, and it was very helpful).

3) P.S. Very prompt shipping, great service - I will definitely use this company again. And thanks to whoever dropped a cheerful Christmas candy into the box!!

The hardest part for me was pulling the dishwasher out from under the countertop. Once it is out all you have to do is disconnect the power (or power off the fuse going to the dishwasher) then look underneath the dishwasher and you will see where the two ends of the heating element come through. Disconnect the wires connected to the ends by simply sliding off the connector. Then remove the plastic "nuts" that screw onto the ends of the heating element by turning them counterclockwise counterclockwise. Once the nuts are removed you can reach inside the dishwasher and remove the old heating element and replace it with the new one. Then simply replace the plastic nuts and reconnect the wires and you are good to go.

tormented by the wheels falling off the lower rack in the dishwasher, had to lift it in and out when loading, then it would get hung up and not enter straight. a real pain in the @$%.
i was so happy to find parts select, and see that other people had the same problem. i ordered the new wheels and modified clip. shipping was really fast. took off the older ones and replaced them. when my husband came home and saw i fixed it myself, he was astonished. no more fighting the rack. smooth and better than new. thx parts select!!

You'll need to remove the front toe kick and (if installed, the GE Profile baffling for additional silencing action).

You will need to disconnect the right wire connection to access the right screw (and may need to use a flat head screwdriver). You can then remove the 2 screws that hold the Valve Water Inlet on.

You will then need to loosen and the hose clamp that attaches the water line to the Valve Water Inlet. You may need to force it undone since the rubber connection is pretty secure around the water tube inlet.

Disconnect the plastic wire housing from the Valve Water Inlet and you should now have the Valve Water Inlet disconnected.

Reverse the order and reconnect everything and you should be good to go!

Double-check for any leaks prior to pushing everything back in :)

Removed the bottom tray, it just pulls straight out, once the tray was removed, the bottom revolving sprayer just lifts right off. Under this sprayer is a self-cleaning filter. There is a plastic piece that screws the filter into place, this part unscrewed easily by hand. Once unscrewed, the filter lifted straight up. I then reversed the process with the new filter and the problem was solved. Note: The old filter was full of sand and grime.

I gently removed the old gasket and replaced it with no problem. The part just pushes into a channel in the washer side.

Disconnected electrics,plumbing, and removed DW.
Replaced sump inlet by removing about four clamps.
The inlet was partially dissolved. I think what lead to this is a partial clog, of broken glass and plastic. DW works fine.

I noticed the circulation pump was not operating. If I turned the motor with a screw driver it would start running. I replaced the pump and now the dishwasher works like new. Very easy to replace the pump but you will have to pull out the dishwasher and turn on its back. I was able to confirm the circulation pump was the problem by observing the motor not running when it should but it would run once I turned the inside motor parts(be careful!). I also had to replace the center sprayer which again was very easy.

First I had to unscrew screws under the counter then pulled built in dishwasher out from under the counter, attached hing arm link to right side bracket on door, and the other end I attatched to a spring at the back of the unit. Thats it! and pushed the dishwasher back into place. All back to normal....by the way Im a 67 yr old great grandmother...

I took out the old rack and put in the new rack. Took about 20 seconds tops. But I had thought I needed to order the wheels (8 of them) and the wheel attachments (8 of those, too) separately because when you go to order the rack, it is suggested that you buy those, too. But the rack came with all the parts I needed so I ended up returning the stud rollers. Very happy with the product and the friendly service.

Turned power off, removed dishwasher, tipped on side, removed and installed pump asym, reinstalled

replaced it