GGG388LXQ02 Whirlpool Range - Instructions

Just replaced insert pan - was able to identify it on the internet web site by inserting model number. Ordered part on line and got it within a week! Easy peasy!

removed oven door, unscrewed 2 screws on front of plate covering burner at bottom of oven. Undid wing nuts on tent-like cover, unscrewed 2 screws at back of burner (igniter "hiding" under left back side). Pulled oven away from wall (yuch, where did that stuff come from?), unscrewed 2 screws of bottom plate, undid connector to old igniter, fished wires with connector from new igniter, plugged them in. Attached new igniter to bottom of burner, rescrewed. Put all screws and parts back in correct places. Cleaned oven door before putting it back on. Turned oven on........baked bread!! Hooray! Repair was easy-peasy!

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

Removed two screws on sensor in the oven. Pulled out stove and after unplugging same removed the back panel. Sensor has an electric connection on the rear of the oven with a connection that is easily separated. Threaded new sensor electrical connection through inside of oven and connected on the back of stove. Pushed insulation back around the wire were in goes through to the oven. Replaced back on stove and screwed in two screws which hold sensor inside the oven. Replaced back cover on stove, plugged it in and pushed it back in place. Did the trick for me..

My used stove had been dropped by the previous owner. While I could live with the minor scratches on one side the wooden shims holding up one corner were annoying. A new leveling leg was less than $2. I used a pair of needle nose pliers to straighten the mounting hole and screwed the new leg in. This used stove was originally $2000 but I bought it for $999. the new leg plus shipping was about $10. What a deal.

We have double wall ovens and each one only had a single oven rack in it. After 3+ years, I was tired of dealing with the issue so I ordered two new racks from PartSelect. They came quickly and fit perfectly. All I had to do was open the box, remove the rack and slide it into the oven. No muss, no fuss. Why didn't I do this years ago??

Followed instructions I found online at the Maytag site.

The range in my classroom had the leveling legs broke off by the summer staff. I ordered two new leveling legs and the night custodian replaced them in about 45 minutes and them leveled the stove. Parts were just as stated and easy to order.

Similar to another customer, the racks were not removed before self-cleaning. The issue was that I AM THE HUSBAND and I admit that I did it. Ooops. Great price and if I do it again, I will go back to parts select to get a replacement.

Removed grills, lower burner cover and burner inlet cover. I then pulled burner out far enough until plug for igniter was exposed. Unclipped wire connection by squeezing in retainer clip and then pulled apart. Pulled burner tube/igniter assembly out and removed two igniter retaining screws. Then reinstalled in reverse order.

Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.

Warning: Door falls apart after removing the two screws which attach the handle. No big deal, just a suprise!

very simple fix. I removed the bake burner cover (the blue cover on the bottom of the oven), under that is the oven baffle which is held on with one wing nut and removed that. Then remove the oven bake igniter screws(two on the side), remove the orifice cover scew and remove then remove the oven bake burner gently. once these parts are off you need to remove the screws on the back of the oven ( I believe theres about 4 or 5 along each side and there are 4 on the bottom of the large metal plate. you only need to remove the large metal cover every thing else stays put. Disconnect the lower back burner attatchment which just clips into the connecter. once thats removed the part should come out easlily from the inside of the oven. Now take the new bake ignitor and feed the wires through the opening on the inside of the oven that allows the wires to come through to the back of the oven(you may need to feel around for the wires and move some of the insulation aside to feel them) once the wires come through the back connect the new part by clipping it to the harness the old part was removed from. At this point you should be able to reassemble the back of the oven exactly the way it was removed.Now go back to the inside of the oven, replace the bake burner gently over the bake burner orifice and put the orifice cover back on and reattach with it's screw. Position the bake igniter back into place on the side of the bake burner and replace the two screws previously removed. Once thats in place its time to put the oven baffle back on and secure with the wing nut and the last step is to place the bake burner cover. Just set the oven to bake and it should be working if thats in fact the problem..Good luck. Took me less than 15 minutes to fix.Some find it easier to remove the oven door but I didn't need to do this since I had enough room to access the front and the back of the oven without any trouble.

The lower oven would not heat up, the temperature stayed at 100. I'm pretty sure the same instructions apply for the upper oven. This is a pretty straightforward repair with a couple of minor bear traps. 1) Remove the oven door by simply lifting it up off the hinges. Not absolutely necessary, but helpful to get your head inside the oven. Not a bad idea to vacuum out the oven floor at this stage. 2) Remove the two Philips head screws at the front of the burner pan cover - the screws are at the very bottom inside the oven. 3) The pan cover lifts straight out of the oven, set it to the side. 4) Remove the burner cover held down by either one or two wing nuts - my oven only had one wing nut from the factory - nice job Maytag on your quality control!! 5) Loosen the screw holding down the burner cover in the far back right corner. This cover is a steel rectangular box that is a shield for the burner gas / air connection. Turn the box around to expose the burner end. 6) Remove the two screws that hold down the burner assembly. One screw is at the very front of the oven. The other screw is on the left side of the burner at the rear. Do NOT remove the pan held down by 6 or more screws. On my oven, the left rear screw was stripped. It stripped in a very weird way that took a long time to remove it. The threads inside the metal were fine, but the threads that had been exposed to heat were brittle and fell off. That meant the screw backed out about 3/4 of the way and then kept turning. This is where pliers come in handy. It will take some pulling up and turning with pliers to get those stripped screws out. I didn't want to cut off the screw because the cut out part would fall back into the lower pan. 7) Pull the oven out from the wall and unplug it from the electicity. Remove the 3 screws holding the left rear metal panel in place. There are two screws along the far left side and one down lower on the right. The panel is connected to the one next to it with tabs. 8) Unplug the ignitor. There is a white fireproof wire that comes up from the bottom of the oven that plugs into a white automotive style clip connector. Push the tab to release the clip and unplug the wire. 9) Wrap some stray wire or string around the plug to use as a pull wire when reassembling the oven. 10) Go back to the front of the oven and lift out the burner, be careful not wo pull your pull wire all the way out of the oven. Untie the pull wire. 11) Remove the two philips head screws that hold the ignitor to the burner bracket. 12) Reassemble! Attach the new ignitor with the two screws. 13) Push the wire into the lower part of the oven. 14) Go to the back of the oven and pull the wire through the oven wall. 15) Drop the burner in, making sure it mates up with the gas tube in the back right. 16) Flip the rectangular burner shield back and tighten it down. 16) Replace the two screws that hold down the burner tube, front and rear. 17) Replace the burner shield with the wing nut(s). 18) Replace the burner cover, or floor of the oven. 19) Go to the back of the oven, plug in the ignitor wire. 20) Replace the rear panel cover and secure it with the three screws. JOB FINISHED! Plug in the stove and push it back. The oven takes a few minutes to start heating, you should be able to see orange glow around the slots in the floor of the oven.

Removed six screws on the valve cover using Phillips head screw driver. Three are along the top on the burner side and three are underneath, needing the upper oven door to be opened to gain access. Removed the old valve using screwdriver and 7/16 end wrench. Used same tools to reassemble. Only problem is the valve retaining clamp is hard to get on unless you position it first, before connecting the valve to the line that runs off to the burner. Otherwise, it would have been fairly easy. These valves will stick if liquids are allowed to drip down and under the valve knobs. The channel in the valve stem takes the liquids down to the valve and can cause frozen valves. I bought 3 extra valves to have on hand in case of future failures.