GFWR4800F1WW General Electric Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Drain pump failed
Remove back cover and with a light and a mirror the screws can be identified. Three hold this pump on. Remove electrical connection then the pump. So also remove the corrugated connecting boot by undoing three clamps. Clean and reassemble
Parts Used:
-
John from LYONS, CO
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Riper gasket main, needed replaced.
After trying multiple times, multiple ways to stretch the gasket over the washer drum with no luck, I was able to get it installed but it took 2 more people. 4 hands to hold the gasket while the other person fits it around the drum. I noticed in the install videos they start the process then cut away, and magically the gasket is installed.
Parts Used:
-
Michael from WELDON, IL
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer was vibrating during spin cycle
Problem got worse the technician installed the damper assembly but the problem got worse . The machine sounds like a tractor .
Parts Used:
-
Linda from Miami, FL
-
Difficulty Level:Very Difficult
-
Total Repair Time:1- 2 hours
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leakage, inner basket bearing play, motor not running
Replaced outer drum, both halves, inner basket/trunnion assy. , Fan housing from excessive vibration/broken mount tabs. Used multimeter to test rotor position sensor ohms, replaced sensor, machine operating as new now.
Parts Used:
-
Rodney from NEW BALTIMORE, MI
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Socket set
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replace basket or drum and bearings and seal on a front load washer
removed the tub and drum assy. replaced the bearings and seal put back a new drum. and put it back together.
Parts Used:
-
Blaine from BRIGHAM CITY, UT
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
TUB OUT OF BALANCE
Replaced the balance ring on the tub but the main tub was cracked and could not be repaired.
Parts select was very helpful. Sent me instructions to repair the washer and replaced defective parts from shipping within 2 days. VERY GOOD EXPERIENCE
Parts select was very helpful. Sent me instructions to repair the washer and replaced defective parts from shipping within 2 days. VERY GOOD EXPERIENCE
Parts Used:
-
Regis from SAN MARTIN, CA
-
Difficulty Level:Easy
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed to change old hoses-7 years old.
Had to shut off the water valves and move the washer.
Needed the wrench because the old hoses were tight. Only tightened the new hoses a little with the wrench.
Needed the wrench because the old hoses were tight. Only tightened the new hoses a little with the wrench.
Parts Used:
-
Fernando from Chester, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench (Adjustable)
2 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!