Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Tub assembly main bearing was sized, and grinding. Wore shaft 16th down.
Pretty straight forward video located on YouTube. Video is about 30 min long. Watched it for an overview and did it myself being mechanically inclined.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door would not close because the part that was in the door that held it closed kept falling out.
Order the part through PartsSelect. It arrived in a few days and I (an 81 year old woman) replaced it within minutes with no help needed. It was super easy.
My front load washer was making a loud roaring sound while spinning out the water
The repair went good but time consuming. I replaced both inner and outer tub bearings along with the tub seal. I removed top by removing two screws in back then pulling back slighty then lifting up. I removed soap tray by pressing down tab and pulling out. Loosened soap dispenser and folded back on top. I removed control panel then front door panel. Remove back panel. Remove motor and shocks and hanging springs which there are two. Disconnect the hoses attached to tub then pull the tub. Remove screws holding the tub halves together. Use punch to remove bearings. NOTE: If you put the bearings in the freezer prior to installing, they go in much easier. I used the old bearing, set it on the new bearing then I tapped the old bearing so not to damage new bearings. I replaced the seal then put everything back together. Not difficult but time consuming.
Seal on front loading washer failed, causing basket bearings to fail.
I removed the tub. Thin included disassembling the washer and disconnecting various hoses electrical connectors to facilitate the removal of the tub from the machine. Once removed, I separated the two halves of the tub and removed the metal basket to gain access to the bearings and seal. Removal of the bearings was much harder than expected as they were very difficult to drive out of their pressed in mounting. I finally was able to remove the bearings and fabricated a press using a piece of all thread and two steel plates to install the new bearings and seal. I would not attempt to do this again with the proper bearing pullers and an official press to install the bearings gently without beating the tub housing. This repair I feel is beyond the scope of your average DIY. The bearings can be damaged easily without the specialized tools to install the components.
It went great. First of all, thank you Part Select for the video on how to do this myself. My home warranty company was giving me a hard time. Blah, blah, blah. A mechanic friend of mine referred me to this site. Within minutes I found the part I need and a GREAT!!!! price. Ordered it, got it super fast, fixed it my self and my second hand washer is no longer peeing all over the floor. Very very happy. I will definitely be a repeat customer, hopefully not anytime soon. Thank you again for an amazing experience.
Followed instruction from you tube. Removed gasket holder, then gasket by door switch assembly then replaced with new assembly! I am a 63 woman and found this easy to do, with help from you tube guy.
Washer would not start, but if you disconnect it and plugged it in it started without pushing start button
It was easy to remove the rubber gasket to get at the door lock. Removing the door lock and replacing was simple enough, but getting the metal ring securing the gasket was cumbersome and challenging. This took most of the time. However, after replacing the door lock it was obvious that this was not the problem. I had to remove the new part and replace the old one. For future, it was the pob circuit board that was defective and had to replace it. Apparently this is not an uncommon problem as there are a number of UTube videos about this.This job was more involved and took me over an hour and resolved the issue.
Our washer was leaking from the washer hose. Once taken off I could see it had a small tear in it. All it took was a screwdriver and a couple minutes and we were up and running. I love PartSelect.com for always having the parts I need and getting them to me in a timely manner!
Took off the old hose with a screwdriver and put the new one on. As simple as that. You don’t need a repair man to get this done, you can do it yourself and save money too.
After I watched the repair video for the part, it was a snap. It went exactly as the video described the steps. Hardest part was moving the washer to get behind it.
To fix the problem, I simply removed the top cover of the washing machine by removing the two screws on the back of the machine which allowed me to slide the top back and then I lifted it off. Then I disconnected the hot water hose (after shutting off the valve). Next, I removed the electrical connectors on the old part as well as the hose attached to it and unscrewed the old part and removed it and put the new one on and reattached the hoses and the electrical. It worked like a charm. It took me perhaps 10 minutes total.
