GC-J288GSKM LG Refrigerator - Instructions

1. Shut off water to refrigerator. 2. Removed bottom sheet metal cover (6 screws). 3. Removed leaking water inlet valve assembly from refrigerator (1 screw). 4. Remove water inlet tube (loosen nut) and tube back to refrigerator (pull from water valve after remove cotter pin washer). 5. Detach two electrical wire harnesses. 6. Install new water inlet valve assembly to refrigerator (1 screw). 7. Replace both water tubes to water inlet assembly. 8. Re-attach both wiring harnesses. 9. Turn water to refrigerator on. 10. Check for leaks. 11. Re-attach bottom sheet cover (6 screws).

Found the broken spring; matched it with parts diagram. Googled for sources via part number. Selected this site because it had best deal - price, availability, shipping. Part arrived as predicted; installed it in 2 minutes. Job done. Door now works.

REMOVED 3 SCREWS AND OUT IT CAME UNPLUG THE HARNES AT THE TOP YOUR NONE

Unplugged fridge, shut off water supply disconnected water supply from fridge. Remove screws that hold lower cover on back of fridge, removed screws holding valve assembly to fridge. Disconnect two electrical connections, remove black c-clip on out flow water line, lift fitting on outflow line side and pull water line off. Replace with valve assembly in reverse order

When I sent an email about this and asked for a replacement, I was told I would need to send it back. I wrote back and reiterated that the glass was shattered and did they really want me to send it back. I again said just send me the replacement. Instead I got a response that sending it back was not necessary but that I would receive a refund and would need to reorder the part again. The part was $47.91 when I first purchased it. Now to reorder it is $54.98. I saved it in my shopping cart so I can shop around before purchasing this again. I am disgusted that I need to go through this again and now at a higher price. I have more parts to order but am reconsidering do so.

Removed two screws from door and three locking brackets with a small common screw driver. Raised the bracket, slide in the spring, held down the bracket, installed screws and plastic covers. Less than 2 minutes. Easy application no problem with the new spring or ,mullion..

I looked at the picture I took. Used needle nose pliers and inserted one end. Unless the lady of the house is very strong, this should be handled by a man, because of the rigid spring. Once the spring was inserted into one side of the flap, I used the pliers to get the other end into the proper slot. Very easy, but the spring is very strong !!

I bought the ice assembly motor only, super easy to install, remove the three main screws, lift out assembly, detach the cable. Then remove the screws on the parts, lift the tape, redo everything in reverse and it works flawlessly!

The glass was ordered correctly. The part was too big for mt refrigerator. I tried to send it back, but I got no reply. I tried cutting the glass to size and it shattered. I wasted 60.00 and im disgusted with your company.

Swapped old one with new one. New one had extra plug not needed.

Took the old one out and put the new one in.

Replaced drawer.

Expensive to have repair man come out and find out that I’ve been mailed wrong spring again. My icemaker is on the left hand side this is the side of refrigerator- I need the spring for left side with the ice maker. Twice they have mailed me the Wrong spring that goes on the right hand side I have tried to explain this to the person that waits on me. Do I have to pay for another spring and mail this one back ?i have mailed one back and postage is getting expensive.

Just popped it in, just as easy as that!

was easy watching youtube video of how to replace whole ice maker, was only 3 screws, remove from the door, a couple of screws hold it to the flat piece, route the wires around the unit, connect the plug as installing it in the door, position it, and tighten 3 screws, that easy