Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
TOP BLOWER FAN NONFUNCTIONAL
1- TURN OFF POWER TO OVEN 2- REMOVE OVEN 3- REMOVE BACK PANEL SHROUDING 4- DISCONNECT POWER TO BLOWER 5- REMOVE BLOWER UNIT 5- REPLACE WITH NEW UNIT 6- RECONNECTED POWER 7- PUT OVEN BACK
After 22 years the oven stopped heating in the middle of a meal prep. The fault code was F3 oven temperature problem. I googled the codes and found PartSelect described the problem and the repair and part needed. I received the oven sensor part, then turned off the power, used a screwdriver to remove 2 screws (had to find the right size flat head screwdriver to fit the square holed screws and they were pretty baked on after 22 years of use), gently pulled the sensor and wiring through the back of the oven. I used a needle-nose plier to pull the plastic connector through the insulation, then unsnapped the connector, snapped in the new sensor connector and pushed it back through the oven wall. Pretty simple repair, took me longer to find the screw driver than the actual repair. Thank you PartSelect for making it easy and saving me a repairman visit!
Cut the power. Undid the screws to the element. Popped off the old element replaced with new,put screws back in turned power back on and Shazam it was up and going
Thanks for the excellent service. Parts cheaper than local stores, arrived on time, with NO PROBLEMS. Installation, probably 30-minutes. Took the opportunity to clean glass, door panels, etc while disassembled, so used about an hour. Oven cleaner was a big help in the cleanup. Very rewarding project and it saves changing the unit and and refitting the countertop.
Once we figured out to use small allen wrenches in the small holes of the hinge to enable us to lift the door off everything went smoothly. Took out six screws, lifted out the hinges - inserted new ones, replaced screws and replaced door. Yipee
Just screwed the new one on. A repair man said it would be really difficult and a lot of people break the glass when putting it in. But that wasn't true. It was really easy.
Remove the left/right outside trim on the double oven. To do this you will need a phillip screw driver. There is only one screw holding each side located at the bottom of the trim (on the inside between the trim and the door). Remove the trim by pulling out and down. Remove the bottom trim by removing the screws located on the outside of the trim. Remove the trim by pulling down and out. Replace the new trim by reversing the process making sure to replace bottom trim first because the outside trim goes over bottom trim to cover up the screws on the bottom trim
I was trying to remove the oven door so I could clean the glass. Spills had run down between the layers of glass.
This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.
Verify power is off to the oven, turned main power supply off for the oven at the breaker panel, located the securing screws for the defective element, used a Phillips screw driver to remove the screws, pulled the element slightly out unit wires are exposed, verify 0 volts at the element wiring terminals, used pliers to remove the wires to complete the uninstalling process, reinstall the element in the reverse order, restored power at the breaker panel
I was able to remove the old element and planned it with what little time off that I could. This would have been maybe 20-30 minute repair at the most. HOWEVER! I was extremely irritated screws were not included? When I called to ask if they were missing they said they didn’t come with the element. Cost me a very annoying trip to the hardware store. Not sure if I missed it on the site that they don’t provide screws - would have been nice to know that before I started. Still scratching my head as to why screws wouldn’t be included? My old ones were as beat up as the element I replaced. I was so irritated I was looking for a spot to leave feedback. Product is fine. Shipping was fine. Sending these products out as they do? Zero stars on that.
Both glass windows in oven door broke due to water falling on 500oF hot glass
we live in Venzuela the ordered windows come to us via a forwarder in the US, one glass (the outer glass) still has to arrive. Very pleased with the service of PartSelect, one glass was in stock, the inner glass had to be ordered with the manufacturer. This glass is on its way and will arrive here in Venezuela by the end of May. As I have to travel to Europe next week, I will install both glasses upon my return somewhere in August next. I will sure inform you about the repair which will be done by myself. regards, Titus