G100 Jenn-Air Cooktop - Instructions

First I removed the burner control knobs by pulling them off. Then I removed the screw washers from around the burner control stems. I lifted the chrome plate from around the burner stems. I disconnected the wire plugs from the rocker switch control. I made a note of which one was plugged to what (color coded). I removed holding washers from the two screws on the switch. Then I unscrewed the small screws that hold in the rocker switch and removed the old switch. I screwed in the new switch, put on the new holding washers, plugged the wire plugs back in, replaced the chrome plate and burner stem screw washers. Replaced the burner knobs and the vent fan worked. The hardest thing was getting the holding washers back on as they are too small to go over the screw but open up as they go on. I did not have the right tool for this so used a hammer and a socket with an opening that would fit on the washer so I could bang it down.

just swapped out the two switches

I had tried several other "universal" brands from the home improvement center but nothing worked with my Jen-Aire. I finally ordered from PartSelect and they fit perfectly! My range-top looks brand new and finding and ordering the correct parts was amazingly easy. Thanks!

We cleaned the rod on the stove and pushed the new knobs into place. This Jenn Air range was made in 1980. Nice to know Jenn Air is still making parts for their ranges. We also ordered new coil elements which fit perfectly size 6 inch and 8 inch.

Just slid off the old burner knobs, and pushed on the new ones. The most difficult part of the whole thing was just being sure that I ordered the correct knobs that used a D fitting. I ordered some a year ago that weren't the correct fitting.

Turned off breaker for range. Removed 4 phillips screws on control panel, tipped it forward and rested it on top of partially open oven door. Removed knob and nut on old switch. Moved wires, one at a time from old to new switch. Put new switch in place, tightened nut and pushed on knob. Put control panel back in place and installed 4 screws... piece of cake.

I feel that the design of the indicator light, with the base attached to the bottom of the lens, is ingenious in that it eliminates the need for fasteners in that confined space, However, the plastic used for the base needs to be more flexible. Part of the base broke off in trying to force the base over the bottom of the lens. Fortunately, there was enough left on the base that I could slip it over the bottom of the lens and complete the installation.

Knobs sent fit the shafts, but due to molded internal stop wouldn't seat. Had to drill out the stop, and also file down the shafts a bit for knobs to seat acceptably closer to stove-top.

It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.

Replaced wires from broken to new part.

First I turned off the circuit breaker that powered the cooktop. Then I removed downdraft grate. Took out the two screws that held the control panel. Gently pulled out the control panel and turned it so I could see the bottom of the rocker switch Next I disconnected the two wires from the bottom of the switch. Next I removed the nuts that hold the switch in place. Removed the old switch and installed the new one. Put the nuts back on. Replaced the wires. Slid the panel back in place. Put the two screws back in their holes and tightened them. Easy enough. Part was perfect replacement for the original. Thanks

took old knobs off replaced in 3 minutes

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

Pulled old knobs off, pressed new ones on. Probably well under a minute for 6 knobs. Anyone with the IQ of a horseradish could have done it. But what was really great was the help and personality of the agent at the other end of the phone. Shipping was as promised, and the entire experience was delightful!

removeed the dial cover, paced the lens into the hole, slid the light and holder into place , 5 min job.