Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FRS6LF7GS4 > Instructions

FRS6LF7GS4 Frigidaire Refrigerator - Instructions

All installation instructions for FRS6LF7GS4 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FRS6LF7GS4
616-630 of 890
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Rails had cracked and drawer would not open without being held with a hand under it.

  • Customer: Patricia from Prairie Grove, AR
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took drawer out, took shelf out. Took old rails off shelf, put new rails on. Very Easy!

the drive blade for ice maker was rusted

  • Customer: Michael from Philadelphia, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
first copy the explored view of all the parts ' ice maker tray ' then just take it apart slowly you need to get the blades back in the correct order and position thats what the exploded view is for in case you forget then you replace the blade and reassemble , it take a good hour .

The ice maker quit producing ie

  • Customer: Tommie from Port Lavaca, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Purchased a new ice maker assembly and installed. Very easy

Broken shelves

  • Customer: Pamela from Brooklyn, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Easy to install (self explanitory)

Upper Crisper Pan was cracked

  • Customer: Michael from Bethlehem, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I replaced broken tray with new one.

frost build up in side on the back of the freezer .and my my filter housing cup crack due to ice build up inside .freezer side not to cold and fridge side to cold freezer and fridge side to factory settings

  • Customer: Carlos from Newton, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
before I started a check and tested the defrost thermostat and the evaporator fan this one was working .a did check the heating coil system with a digital multimeter tested ok, at the end find out that the thermostat was not working. I put a new one. I just notice after few days some frost is on the wall of the freezer side .can some one help I don't know what else to do .can be the defrost timer .but how you test the one on this model. this one electronic thank you

When the ice maker was filling the ice tray with water, the water would come out the water dispenser at the same time.

  • Customer: Greg from Murrieta, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First I watched the PartSelect installation video. Then unplugged the power and shut off the water valve on the wall. I used a 1/4" nut driver and removed (4) screws on the back bottom cover of the refrigerator and removed the cover. I removed the (2) mounting screws on the back lower right side of the refrigerator and removed the triple water valve assembly. I then marked the (4) water lines and (3) solenoid connectors with numbers, to make sure they get connected back in the same place, and then I removed them. I used a retractable blade knife to cut the ends of the water lines perpendicular. I pushed the (4) water lines into the valve holes and plugged the solenoid connectors back onto the new triple valve assembly. I mounted the new triple valve, put the back cover on, turned on the water, checked for water leaks. There were no leaks.Then I plugged in the power and waited for it to fill up the ice tray. It works perfectly now ! And it was really easy ! Thank You PartSelect for making this repair easy for me.

Door poping loudly.

  • Customer: Craig from New Caney, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Easily removed door and installed new parts. Perfect fit.

2 broken door bins

  • Customer: Angel from Aurora, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
New bins slide and snap into position with no tools required. EASY!

Ice crusher would not crush ice

  • Customer: Gary P from Fall River, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Opened freezer pulled out ice tray put in new one closed freezer door all done

broken crisper drawer support

  • Customer: Genevieve from Herndon, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
1. Punched the little circle bolt at the top of the drawer support all the way through the refrigerator wall using a hammer and awl. Removed the remainder of the old drawer support. 2. Previous two small alignment prongs were stuck into the alignment holes, so I had to snap off the alignment prongs on the new drawer supports with pliers to make the supports fit flush with the fridge wall. 3. Stuck new drawer supports into holes in the fridge wall and hammered in circle bolts with hammer.

Hinge on bin broke

  • Customer: Barbara from Mount Juliet, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simply placed new bin in place. Took less than 60 seconds.

Replacing the level that dispenses water.

  • Customer: James W from BLANCO, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
May need someone to hold a flashlight on area during repair. The bottom ridged-tray does pull out easily, exposing three Phillip-head screws. Remove them. Lift the face plate up slightly and pull out to expose the wiring harness behind it near the top. Push the small clip that holds the white plug together and pull to separate. Set faceplate aside. Find and remove three more Phillip-head screws, one in top middle and two on the sides. Pull the unit forward enough to see the two Phillip screws that hold the metal pieces over the rotating arms of the broken lever. Cannot pull this unit out too far as the water hose from refrigerator restricts movement. Use needle nose pliers to reposition/release the spring clip that rests against the lever. No need to remove the entire spring. Remove the two screws. They are short, so be careful not to drop them or the metal pieces they hold down. Use needle nose pliers to retrieve them if dropped. Lift the broken lever up to disengage its rotating arms from grooves. Remove the broken lever by pulling up or pushing down, depending on where it is broken. Take new lever and insert from the bottom and insert both arms in grooves. Re-insert the two screws and metal pieces (large piece on the left). Place spring clip on arm of new lever. Screw the unit back with three screws. Re-connect the white plug of the faceplate. Reinsert the faceplate on refrigerator by aligning holes with hook-prongs and push in and down to lock in. Add the three screws at bottom to secure. Reinsert the bottom and push in to lock. Check lever operation.

Auger Not Driving Ice Out The Front

  • Customer: JeRay from Arizona City, AZ, AZ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Taking it apart is sort of common sense, however putting it back together can be made a lot easier using todays technology of . Digital photography. Take pictures at each stage of disassembly and reassembly be comes very easy and you may only have to do it once instead of multiple times.

Frige and freezer not cooling

  • Customer: FRANK from BRADENTON, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I should have ordered start kit instead of start capacitor. The start cap astir did not fix problem so I ordered kit. Compasator comes as part of kit. Followed enclosed instructions. Cut existing wires and reconnected new wiring. Simple as that. It's a plug in item. Now worried it may be working to good. Freezer down to 10 deg. Watching to see if compressor is running to long. Seems ok lol. Wife hates me now. She wanted new frige.
All Instructions for the FRS6LF7GS4
616-630 of 890