Models > FRQE7000LW0 > Instructions

FRQE7000LW0 Frigidaire Dryer - Instructions

All Instructions for the FRQE7000LW0
61 - 75 of 88
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door handle broke
Took screws out back of door handle.put new door handle up and put screws back in.it was a breeze.
Parts Used:
Door Handle
  • Kathy from Darlington, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer was not drying completly.
I replaced the Control Thermistor (part # PS1149368) by removing the two screws on the bottom of the lower panel below the door. You will see the Control Thermistor just below and to the left of the discharge chute. Remove the two screws holding the Control Thermistor in place. Disconnect the two wire and reconnect to new Control Thermistor. Replace screws in reverse order of above.
Parts Used:
Control Thermistor
  • Scott from Otsego, MN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Poly carbonite door handle snapped
Remove two phillips head screws on the inside of the door, fit the new part and reused the screws to attatch it. Careful not to overtighten the screws.
Parts Used:
Door Handle
  • Nicholas from Story City, IA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
I shut the door too hard, and the old latch fell down into the inside of the dryer.
The new latch easily snapped it into place.
Parts Used:
Door Catch
  • Bret from Tampa, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
replaced broken door washer handle. second incident
removed both screws. positioned handle. inserted the screws. tighten with screw driver done within two minutes.
Parts Used:
Door Handle
  • patricia from simi valley, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
no problem
put door catch in hole
Parts Used:
Door Catch
  • David from Mayfield, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
door handle cracked.
Rather than call repair co. and pay at least $100 plus parts, i decided to order parts myself. It came in less than a week. Watched the video on website. Did the repair by removing old handle with phillips head screw driver and installing new. Took about 5 min. I am a 72 tear old woman. Thanks for being online.
Parts Used:
Door Handle
  • Barbara from Lolo, MT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer Would Not Heat
I researched possible causes on line and watched a PartsSelect video on YouTube on how to test. I ended up misreading test results and ordered the High Limit Thermostat but subsequently realized problem was the Terminal Block. No problem, PartsSelect took back the Thermostat (I hadn't installed it) and shipped me the Terminal Block. My dryer was back up and running in less than 7 days from initial analysis to installation of Terminal Block. Instructions that came in confirmation email for installation were perfect and easy to follow. Total cost with new power cord from Home Depot was less than $50 vs a quoted service call of $175+ parts from local electrician.
Parts Used:
High Limit Thermostat
  • John from Hummelstown, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
broken washer handle
put the new handle in place on door and screw it in.
Parts Used:
Door Handle
  • Stephen from Pismo Beach, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
door handle broke at where screw holds it to the door
really bad design on the door, door breaks when pull is slightly upwards and washer is on the bottom of washer dryer stack so pull is always up.this is my third one. remove two screws and replace . takes about 2/3 minutes
Parts Used:
Door Handle
  • Robert from Gibsonia, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
front loading washing machine.
This is th esecond handle I have installed on this washing machine. The model number has disappeared from the label from being exposed to detergent and age. This web site provided EXCELLENT guides to ensure the correct part was ordered. The picture perfectly matched my handle. The part arrived VERY quickly and with EXCELLENT packing to ensure the plastic part was not damaged. The installation required two minutes to remove the damaged handle and install the new handle.
Parts Used:
Door Handle
  • ROBERT from valley springs, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Shreking noise when turning on, then loud noise from dryer, after a few minutes it would not be so loud but louder than normal.
Replaced everything on the dryer till I got the right problem, seriously, I now have a new dryer in an old body, still came out alot cheaper than buying a new one. I listened to every sound on youtube but none sounded like my dryer.
Parts Used:
Blower Housing with Blower Wheel
  • joan from Roanoke, AL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The plastic handle broke off
There was video but all you do is unscrew the old screws and line up the handle and screw them in..
Parts Used:
Door Handle
  • Janice from Nantucket, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door would not close because of broken female latch.
Very simple. I removed the broken latch with pliers and snapped in the new one in less than 5 minutes.
Parts Used:
Door Catch
  • Raymond Frattone from Richboro, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
Handle was broken at the screw attachment areas.
I took a #2 phillips head screw driver & removed the old pieces from the broken handle, & installed the new one with the 2 screws. It fits perfect & I con't have to hear my wife complain about opening the door anymore!
Parts Used:
Door Handle
  • Mike from Monroe, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the FRQE7000LW0
61 - 75 of 88
Back to Top